PDA

View Full Version : Pictures of 2010 Moomba swivel racks



you da man
02-05-2010, 05:48 PM
The racks arrived yesterday and I just finished assembling them. Took about 20 min total with double checking. As I mentioned, no instructions but it was easy enough to figure out. Packaged very well and protected and total of 10 pieces with 20 allen head bolts. I used blue loctite as I always do for moving parts or parts that can vibrate.

http://i168.photobucket.com/albums/u197/seeajgo/DSCF0712.jpg
http://i168.photobucket.com/albums/u197/seeajgo/DSCF0713.jpg
http://i168.photobucket.com/albums/u197/seeajgo/DSCF0715.jpg
http://i168.photobucket.com/albums/u197/seeajgo/DSCF0716.jpg

brain_rinse
02-05-2010, 06:24 PM
Those are sweet!

Aquaholic
02-05-2010, 06:33 PM
They are sweet. I'm curious if they are going to be level on the tower and if you will have a few different places to mount them. Post the boat pix. Congrats they are going to look nice...


Aqua

you da man
02-05-2010, 06:36 PM
They will be drilled on to the crossbar where the stock racks go. They will swing/hinge level.

kaneboats
02-06-2010, 01:23 AM
Don't care about the racks but I could easily crash right there on the chaise.

viking
02-08-2010, 03:49 PM
can't wait to see them on the boat. Keep us posted :)

newty
02-08-2010, 04:21 PM
Yea those are them! I love the look of them.
Post up pics whe nyou get them installed.
What did you end up paying for them?

Sled491
02-08-2010, 09:56 PM
Where does the beer go on these? :D

you da man
02-08-2010, 10:25 PM
Where does the beer go on these? :D

That would be cool...one of the swivel coozy thingies.

moombadaze
02-09-2010, 08:12 AM
Question, what does the rack pivot on-meaning is it a screw or a pin that is press fitted.

Sled491
02-10-2010, 07:45 AM
Looks like a driven pin from the last picture

you da man
02-10-2010, 10:44 AM
Looks like a driven pin from the last picture

The pin has an allen head so I guess it can be adjusted

moombadaze
02-10-2010, 10:49 AM
The pin has an allen head so I guess it can be adjusted


In looking at the photos, the reason I was asking is if that is a allen head could it possibly work itself loose and fall out? taking the rack and boards to the bottom of the lake or is that not possible?

Really like those racks-hate standing on the side ballancing boards,body.

you da man
02-10-2010, 11:58 AM
In looking at the photos, the reason I was asking is if that is a allen head could it possibly work itself loose and fall out? taking the rack and boards to the bottom of the lake or is that not possible?

Really like those racks-hate standing on the side ballancing boards,body.

That brings up a good point because the pin would fall out the bottom. I'm sure I could drill the bolt and safety wire it.

K_E_N
02-11-2010, 04:38 PM
Question, what does the rack pivot on-meaning is it a screw or a pin that is press fitted.

I have pretty much the same racks on my '04 LSV. With mine, the pivot point is an allen head bolt. Also, with mine, the bolt comes in from the top. My question would be, "is it possible that something was put together upside down with these?" I've never seen my bolts become loosened, but could certainly see the concern.
On a side note, I've also needed some rubber inserts for my racks due to age and sun exposure. Roswell took care of that issue, great company.
On to side note #2. The only problem that I've noted with these racks is the fact that the pin you remove to allow for it to swivel is attached with a wire. Wire breaks over time. I've had to fix one of my wires. Fortunately, I didn't drop the pin when the wire broke.

Congrats on your purchase. You'll love this mod more than most you'll do to your boat.

you da man
02-12-2010, 02:00 PM
I have pretty much the same racks on my '04 LSV. With mine, the pivot point is an allen head bolt. Also, with mine, the bolt comes in from the top. My question would be, "is it possible that something was put together upside down with these?".

I thought to be kinda odd myself, however, the swivel part came preassembled from Roswell. I only had to attach the racks (3 pc each side) to the swivel.