PDA

View Full Version : Calling on owners with stock Jabsco pump systems



2007 Outback V
03-27-2011, 04:49 PM
Where are the through hull intakes placed? Anyone have any pics?

lsvboombox
03-27-2011, 09:58 PM
Where are the through hull intakes placed? Anyone have any pics?

mine are on either side of the vdrive unit.. dont have pics at the current momemnt

moombadaze
03-28-2011, 08:27 AM
bet he is adding them and wanting to see where the factory put them

2007 Outback V
03-28-2011, 12:59 PM
I'm going to be adding an intake or two and want to know how the stock intakes are oriented. Would be great to see some pics taken from under the hull and inside the bilge area.

Ed, you have a nice pic of the pumps, but none of the intakes. You volunteering to take some pics for me?

Stacy, you are right on! ;)

moombadaze
03-28-2011, 03:57 PM
07, keep one thing in mind-the factory drilled all there holes when it was a blank hull-no motor,no trans and no trailer in the way. I made a misjudgement in one of my thru hulls I added and could not drill up into the boat after drilling the pilot hole down thru the bottom-no big deal in the end but could have been bad.

2007 Outback V
03-28-2011, 04:59 PM
07, keep one thing in mind-the factory drilled all there holes when it was a blank hull-no motor,no trans and no trailer in the way. I made a misjudgement in one of my thru hulls I added and could not drill up into the boat after drilling the pilot hole down thru the bottom-no big deal in the end but could have been bad.

Good thinking. I just wanted some ideas. I know I want to stay away from the paddle wheel, engine intake, and obviously the ribs in the hull. Besides that I don't know where would be a good spot vs. a bad one? :confused:

moombadaze
03-28-2011, 08:21 PM
Dont think you want one in front of the paddle wheel and as long as the access is ok that should be a good spot

NCSUmoomba
03-29-2011, 03:09 AM
If you look at the photos from my factory tour, I have some shots of the ballast system being installed.

http://www.moomba.com/msgboard/showthread.php?t=12576

tazz3069
04-02-2011, 07:11 PM
I'm going to be adding an intake or two and want to know how the stock intakes are oriented. Would be great to see some pics taken from under the hull and inside the bilge area.

Ed, you have a nice pic of the pumps, but none of the intakes. You volunteering to take some pics for me?

Stacy, you are right on! ;)

Look at my album. I took out the lawn sprinkler system and replaced the single pump with 3 new pumps. The picture of the intake is the original intake, I just changed it from a 3/4" to a 1" intake and remove the scoop. I just looked at my intakes. The stock intake is directly opposite of the intake for the engine.

2007 Outback V
04-03-2011, 12:38 AM
If you look at the photos from my factory tour, I have some shots of the ballast system being installed.

http://www.moomba.com/msgboard/showthread.php?t=12576

These two pics are spot on! Thanks

http://lh5.ggpht.com/_H4yfOjtYIfM/THK2JzpX8mI/AAAAAAAAAfI/e6n6GUlErkw/s640/SC%20factory%20tour%20%2842%29.JPG

http://lh4.ggpht.com/_H4yfOjtYIfM/THK2NaDUPGI/AAAAAAAAAfY/XRjh-r3oATY/s640/SC%20factory%20tour%20%2846%29.JPG