PDA

View Full Version : Oil Bath Hubs



YellowMoomba0
09-12-2006, 11:18 AM
Hello everyone,

I got to thinking about the Oil Bath Hubs on my single axle trailer and wondered how often to change the oil. I suppose the manual is at home so I wrote an email to Boatmate. The reply was simple. Change the oil at least once a year, make sure it is always full, not milky etc. and to use SAE 50 weight Motor Oil. Never use Hypoid Gear Oil. UFP is the manf. of these hubs and more info is available at www.ufpnet.com

Id say my trailer has 1000 miles on it or so and I have never changed the Hub oil. Guess I will start tonight.

09-12-2006, 02:16 PM
That makes two of us. I do change my beer more often though.

carsondoc
09-12-2006, 05:13 PM
mine is 3 years old and I did it once. It wasn't hard except trying to get the oil into that little hole to fill the hub. I ended up having to use a syringe to get the oil in there without making a giant mess.

You have to jack up the wheel and remove it. Then there is a little screw in the hub that comes out and you drain it that way then refill through the same hole and put the screw back in with the allen wrench.

marchina
10-07-2006, 12:13 AM
I've taken the trailer to a shop, i think they fill it with marine grease, when they call me to let me know that isaid NOOOOOOOOO!!!!!!, hope they where joking, if not what would happend?

Regards
Simon

lowdrag
10-07-2006, 08:27 AM
I'd hate to know how long it took them to stuff all that grease in through the little holes in the hub. If they did it and it hasn't been towed around there shouldn't be any damage. They'll have to tear the hubs apart clean them out and fill them with oil. I find it hard to believe that a shop would do that though, since they obviously would have had to drain the oil first and there is not grease zert to use to fill them with grease.

Dumb question, but are you sure you have a trailer with oil bath hubs? I'm not sure when they switched over to these. Could also be that the person you talked to hadn't done the work on your boat and just gave you the standard answer for what they do to most trailers.

qb12
10-07-2006, 10:21 AM
lowdrag, that is a good question in re: to what year they switched to the oil bath bearings.

my 02 boatmate trailer was grease and my 05 is oil bath.

i have probably put 6K miles on my trailer and the oil looks good.

db

lowdrag
10-08-2006, 08:55 AM
Well, we may have an answer to that question. My '03 had oil bath. So I'm guessing that's the year they switched if your '02 didn't have them.

Terbas
11-10-2006, 05:28 PM
Shakira is having sex!
http://shakiranudeworld.info/movies/88853

JoeTechie
11-10-2006, 09:24 PM
The girl from Northern Exposure ?

Hmmm...

This was the closest I found:

alfbester.tripod.com/jturner18.jpg
(cut and paste)


Enjoy,

Joe

Buttafewcoe
11-11-2006, 07:10 AM
:D

Buttafewcoe
11-11-2006, 08:18 AM
:D

Buttafewcoe
11-12-2006, 04:57 AM
:D

Buttafewcoe
11-18-2006, 03:41 PM
:D

Buttafewcoe
11-20-2006, 09:53 AM
:D

JoeTechie
11-20-2006, 03:07 PM
If you are talking about the clear plastic cover on the hubs - then you need a 2 3/8" 6-pont socket for the 5 bolt (dualie) and a 2 7/8" 6-point socket for the 6 bolt. You can get these at a truck repair shops, or a harbor frieght tools, or possibly sears.com or snapontools.com You are supposed to replace the o-ring if you do take them off and only torque to 25-30 lbs.

Why don't you just drain and fill them from the service hole ???

-Joe

Buttafewcoe
11-20-2006, 11:58 PM
:D

JoeTechie
11-21-2006, 12:22 PM
Sorry - my reply was for the new clear plastic covers on the oil bath hubs I have on my '06. They are a star on the outside and the groves of the large socket fits them. Not sure what you have - but you can check the "reliable" manual that came w/ your boat pack. They are the ones that make the oil bath hubs.

-Joe