PDA

View Full Version : How To: Swivel Seat Mount...



ian ashton
10-21-2008, 02:28 PM
***WARNING: TRY THIS AT YOUR OWN RISK. IF YOU MESS UP YOUR BOAT BY FOLOWING THESE INSTRUCTIONS IT IS YOUR OWN FAULT!***

Tools Required:
13mm Socket Wrench w/extension (I used a 12” extension)
Phillips Head Screw Driver bit and Drill
Lareg Drill bit (I think I used 3/8” or ”?)
Small Drill bit (I have no idea what size I used, it was small)

Parts Required:
Swivel Seat Bracket (WestMarine part #: 412124)
9” x 13” adapter plate (This you will have to procure your self. I had mine made out of ” AL)
8: 3/8 x 1" bolts (rounded head)



This is what the Swivel Seat bracket looks like. I bought it from West Marine for about $25.
http://moomba.com/msgboard/attachment.php?attachmentid=1677&d=1224609231

Here is my stock Outback seat; I think that all of the 08 and earlier Moomba’s have the same seat/seat track/brackets, but I’m not 100% sure, so again your process might be different.
http://moomba.com/msgboard/attachment.php?attachmentid=1679&stc=1&d=1224609946

Step 1: Remove the bottom seat cushion. Its easy, just pull up on the cushion and stash it out of the way.
http://moomba.com/msgboard/attachment.php?attachmentid=1680&stc=1&d=1224609946

Step 2: Remove the 4 13mm bolts to take the seat off of the seat tracks. Put the seat out of the way.
http://moomba.com/msgboard/attachment.php?attachmentid=1681&stc=1&d=1224609946

ian ashton
10-21-2008, 02:33 PM
This is what you will see when you remove the seat.
http://moomba.com/msgboard/attachment.php?attachmentid=1682&stc=1&d=1224610166

Take care not to loose any of the spacers, washers, nuts, and bolts. I put mine in the cupholder.

Step 3: Remove the 10 screws holding the fiberglass base to the floor of the boat.
http://moomba.com/msgboard/attachment.php?attachmentid=1683&stc=1&d=1224610166

Step 4: Flip the base upside down and remove the 4 13mm bolts holding that secure the seat tracks.
http://moomba.com/msgboard/attachment.php?attachmentid=1684&stc=1&d=1224610166

Step 5: Now you'll need to use the swivel mount to mark and drill the new mounting holes. You'll be mounting the swivel directly to the base.
http://moomba.com/msgboard/attachment.php?attachmentid=1685&stc=1&d=1224610166




I am wating on the arrival of my adapter plate, so as soon as I get it I'll continue the thread.

choard
10-21-2008, 11:58 PM
Ian I am waiting in eager anticipation! The lack of swivel is one of my main gripes with the new Moomba seats. I have the XLV so hopefully I can still do this mod cause I have limited room to swivel cause of the back of the seat rest behind the drivers seat. I will be doing this mod for sure over winter, thanks for the pic's and post.
Cory

deerfield
10-22-2008, 12:04 AM
ian - Interesting thread. This could well be a modification I can handle and would make to my '07 Outback. Look forward to seeing the completion of your project. Thanks for posting. - Deerfield

501
10-22-2008, 12:14 AM
Wicked idea. I too have an 08 XLV and would love a swivel seat. Let us know when it's all finished.

McMoomba
01-03-2009, 04:49 PM
Ian, any updates on this?

Sled491
01-03-2009, 11:06 PM
Ian, your a smart guy so please don't be insulted by my question. Are you sure the seat will clear for a 180 swivel?

ian ashton
01-04-2009, 02:30 PM
Ian, your a smart guy so please don't be insulted by my question. Are you sure the seat will clear for a 180 swivel?

I'm sure it won't (still an unfinished project, lol)

I'd just like to get 90 degrees to face the spotter seat while anchored.

Sled491
01-04-2009, 04:56 PM
Gotcha, I kind of figured this as in my old Nitro you could swivel the drivers seat but you had to half swivel it, then pull it forward and finish the swivel.

c.rix
01-04-2009, 08:57 PM
Ian correct me if im wrong but you want the seat to not be mounted to the slider anymore mounting it too the swivel in its place, so the seat will now be stationary??? Dont you think that you could have made a plate to mount to the slider and then drill/tap holes into the plate for the swivel, Then make another plate for the seat and drill/tap into a plate for the swivel to mount to to complete the pair

Also If you did this you may be able to cheat over to the side so the seat wont rub the sides when rotating

the best part about making adaptor plates is there really wouldn't be any drilling of factory parts if things didn't go as planned take them out and your back to stock.

Sorry just some constructive thinking

Also a benifit of making adap. plates is the added height when sitting in the seat

chillyx
01-23-2009, 10:34 PM
Ian, now that you've finished he seat swivel, do you just love it? is it pretty stable, or does it rock side to side. Inquiring minds want to know.

ian ashton
01-24-2009, 02:48 PM
I haven't finished it, I'm lazy and its cold; my garage isn't heated :(

jester
01-24-2009, 04:09 PM
Ian,

I am looking forward to seeing it finished. If your garage is cold you could always do what my collage roommates and i did to hear it up. get a bottle of rubing alc and light it on fire. Burns clean with no mess afterwords. Also does great on heating up the area or lighting your friends on fire.

Natz08
01-29-2009, 02:25 AM
I would just cut my losses and buy this guys than you know it will work


http://www.overtons.com/modperl/product/details.cgi?i=34967&pdesc=EEz_Low_Profile_Seat_Slide_Locking_Swivel&cname=Boat-Seat-Pedestals-Sliders&aID=11E&merchID=1009&r=view

Reese350
01-29-2009, 07:39 AM
Natz, did you put this in? I just wonder if it requires drilling or if it fits some standard bolt pattern. I also wonder if it makes the seat sit up higher.

tazz3069
01-29-2009, 09:01 AM
I was wondering the same thing. Also, Look at the handle. It is on the wrong side. I wonder if the handle is universal? Can it be placed on the other side of the slide. I would love to get the spec sheets on it.

I found the website here is the install link.
http://www.garelick.com/product.php?pnumber=75090
http://www.garelick.com/files/12.232.pdf

Sled491
01-29-2009, 09:58 AM
I think with that platform you would have to go all the way to just floor and then just put that in with your seat.