PDA

View Full Version : drilling through carpet for ballast hose



jeilers1
02-16-2009, 11:23 AM
I was going to add some custom fat sacs underneath my seats and wanted to drill (hole saw) a hole underneath the seat supports that sit perpindicular to the bow/stern line of the boat. It would be about a 1" hole that would allow a hose to pass through and connect one bag (the rear) to another so that they could both fill/empty off of the stock gravity ballast plumbing.

I was wondering if anyone has drilled through the carpet and how it reacts? (frays, unravels, or is fine?) I see the new 09's come with a hole precut and carpeted over already.

Any info appreciated.

Thanks

moombadaze
02-16-2009, 06:32 PM
John- sorry i just saw that all the photos in the other thread are gone but this is what i did.

dremil to cut with
http://i527.photobucket.com/albums/cc351/moombadaze/DSC00422.jpg

cooler begining to comeout
http://i527.photobucket.com/albums/cc351/moombadaze/DSC00424.jpg

rear gravity 3 bag under the seats- i plummed it in
http://i527.photobucket.com/albums/cc351/moombadaze/DSC00428.jpg

rear surf bag and under seat bag filled iwth air for the photo
http://i527.photobucket.com/albums/cc351/moombadaze/DSC00431.jpg

moombadaze
02-16-2009, 06:34 PM
this is what it looks like all filled up
http://i527.photobucket.com/albums/cc351/moombadaze/DSC00461.jpg

also put a 400lb bag on the seat


hope this helps with your mod

kaneboats
02-17-2009, 01:12 PM
I really can't wait to see this surf wake.

moombadaze
02-17-2009, 01:46 PM
Still working on it, think i need more weight up front. Looked like the swim platform was still draggin in the water. Other issue i had was the lake level--its low

moombadaze
02-17-2009, 01:55 PM
yep more up front-i would just take the sac i have on the seat and try it up front--still experamenting

kaneboats
02-17-2009, 01:57 PM
You have 25 days to get it dialed in. I haven't even changed my oil yet, much less done anything about wake. I don't know if I'll even have one by 3/14. I did start cleaning yesterday and finished the sub and amp install though.

moombadaze
02-17-2009, 02:06 PM
25 days i wish--more like 4 days off. i need to get amp and tower speaker wires tidy'd up.

Mikey
02-17-2009, 09:35 PM
Going back to you drilling through carpet. I've never made a hole that large through carpet but have done something similar on a much smaller size and asuming the carpet is mostly nylon you could try using a hole saw bit and heat the end and sear/melt the carpet ,like a doughnut hole then the carpet will not run when you very carefully drill through the carpet to make a nice clean hole.Just a thought.I've done something like this fastening a closet track over carpet and heat nails/screws so they don't snag and cause runs.Depends on the carpet by nylon melts quite easily. Very similar to heating the ends of a rope and twisting carefully in your fingers.

newty
02-17-2009, 10:40 PM
I would start the hole saw until it touches the carpet then score the carpet around the saw with a knife then continue drilling carefully. I've done that with no probs.

kaneboats
02-18-2009, 10:46 AM
Agree- put a new blade in your utility knife and get a good cut.

jeilers1
02-18-2009, 11:02 AM
Thanks for the info guys