Tab Content
  • MLA's Avatar
    Yesterday, 10:14 PM
    Yes and no. There's more to winterizing a boat for its winter lay up, then just draining water from the block. For an engine with semi-closed...
    1 replies | 71 view(s)
  • MLA's Avatar
    10-28-2014, 04:09 PM
    I think they are an opaque/cream colored plastic. Ive never taken the chrome off, but seen a few that had worn/faded. Thats chrome is way t slick to...
    19 replies | 275 view(s)
  • MLA's Avatar
    10-28-2014, 12:31 PM
    How did you actually prep the plastic chrome dipped grills? You need to take that chrome off, clean the grill, then prime with a primer thats...
    19 replies | 275 view(s)
  • MLA's Avatar
    10-27-2014, 08:47 AM
    MLA replied to a thread Fogging the Mondo.. in How To Information
    The theory for not inducing into the throttle body of a running engine is that the oil can coat the air intake temp sensor. Fogging at all, could be...
    9 replies | 221 view(s)
  • MLA's Avatar
    10-20-2014, 05:06 PM
    MLA replied to a thread Exile XM7 in Audio & Electrical
    Can you explain for the forum, the relevance? Are you saying a 4 ohm woofer performs better than a 2 ohm? Not me calling it anything, check...
    7 replies | 322 view(s)
  • MLA's Avatar
    10-15-2014, 07:11 PM
    MLA replied to a thread Exile XM7 in Audio & Electrical
    Its easy to see the discount price for comparing the demo to new, but if you want to compare them to what else is on the market, look at the Memphis...
    7 replies | 322 view(s)
  • MLA's Avatar
    10-14-2014, 08:57 AM
    MLA replied to a thread Now that's a scum line in General Chat
    id clean now. Longer it sits out of the water and drys out, the harder it is to clean. Its was smart on your part to hit it with the pressure washer...
    6 replies | 322 view(s)
  • MLA's Avatar
    10-12-2014, 01:24 PM
    MLA replied to a thread What weight engine oil? in General Chat
    Ive seen some studies that indicate synthetic will find its way back to the oil pan at a much greater rate than conventional. leaving less of an oil...
    13 replies | 397 view(s)
  • MLA's Avatar
    10-11-2014, 08:51 PM
    MLA replied to a thread What weight engine oil? in General Chat
    Nothing wrong with a 25w-40, but a 15W-40 would give you a little easier flow upon a cold start up. An actual marine oil will have a higher level of...
    13 replies | 397 view(s)
  • MLA's Avatar
    10-07-2014, 01:52 PM
    The Kicker IX500.4 is a perfect amp for the KM6500.2 setup as it will deliver 250W rms to each side. It would also be perfect for 2-3 pair of...
    9 replies | 283 view(s)
  • MLA's Avatar
    10-06-2014, 10:44 PM
    Although they are an in-boat coaxial loaded into a tower pod, they are not a bad speaker setup for the money. For a single pair, I would like an amp...
    1 replies | 92 view(s)
  • MLA's Avatar
    10-06-2014, 05:10 PM
    The prototype base plates have been test-fit, so we are ready to go to production. I am also looking into having the blank lower base plate done that...
    5 replies | 355 view(s)
  • MLA's Avatar
    10-06-2014, 09:13 AM
    MLA replied to a thread Is it normal in Service & Repair
    ok, let me clarify. Theres the old drop style that was cooled via lake water, which would drip inside the boat, but when on a fake a lake, there'd be...
    4 replies | 302 view(s)
  • MLA's Avatar
    10-05-2014, 04:14 PM
    MLA replied to a thread Is it normal in Service & Repair
    Yes, as some inboards have a water cooled shaft seal.
    4 replies | 302 view(s)
  • MLA's Avatar
    10-02-2014, 05:47 PM
    MLA replied to a thread Roswell Mojo in Moomba Classifieds
    Looks like a Roswell tower and bimini, especially sine their name is on the side of the boat, and the trailer looks like a Boatmate. They deal direct...
    12 replies | 559 view(s)
  • MLA's Avatar
    10-01-2014, 03:18 PM
    Ive outfitted dozens of 1:1 ratio v-drives and DDs, from 20 ft to 24 ft, with 653's and 911's. Most running 1000# + in ballast. Only know of one that...
    15 replies | 509 view(s)
  • MLA's Avatar
    10-01-2014, 02:18 PM
    These are probably going into full production by the end of the week, for those that are interested. Also working on getting a quote for powder...
    5 replies | 355 view(s)
  • MLA's Avatar
    10-01-2014, 01:20 PM
    I would caution against using the v-drive/direct-drive configuration to determine whether a 3 or 4 blade is the ideal prop, but rather the gear ratio...
    15 replies | 509 view(s)
  • MLA's Avatar
    10-01-2014, 08:27 AM
    If that boat has a typical 1.48:1 gear, a 3-blade is not the right prop. The only v-drives we put 3-blades on, are those with the 1:1 gears.
    15 replies | 509 view(s)
No More Results
About MLA

Basic Information

Age
45
About MLA
Location:
Lake Wylie NC Area
Occupation:
Marine Audio and Ballast

Statistics


Total Posts
Total Posts
801
Posts Per Day
0.55
General Information
Last Activity
Today 03:37 PM
Join Date
10-27-2010
Referrals
0

1 Friend

  1. slipperyrockTKE300 slipperyrockTKE300 is offline

    Senior Member

    slipperyrockTKE300
Showing Friends 1 to 1 of 1