Tab Content
  • MLA's Avatar
    Yesterday, 07:18 PM
    MLA replied to a thread Electrical Gremlin in Service & Repair
    Frozen as in the motor is stick or bound up, not temperature frozen, sorry.
    5 replies | 124 view(s)
  • MLA's Avatar
    09-18-2014, 11:44 AM
    Are these sacs or tanks? Cant put a c/v in the vent line of a tank, but a sac you. It can aid with draining, but is not always needed.
    5 replies | 124 view(s)
  • MLA's Avatar
    09-16-2014, 09:44 PM
    Yes it sure does. If you are in tune with the wave, you can actually tell when you go over a shallow spot.
    11 replies | 310 view(s)
  • MLA's Avatar
    09-15-2014, 10:24 PM
    MLA replied to a thread Electrical Gremlin in Service & Repair
    I would diagnose these 2 issue independently of each other. Just seems like a coincident. For a breaker or fuse to trip/pop, there needs to be a...
    5 replies | 124 view(s)
  • MLA's Avatar
    09-15-2014, 10:15 AM
    Just change the position of the sub input button on the amp. The sub will then receive its signal from the full-range inputs that feed chnls 1-4.
    18 replies | 416 view(s)
  • MLA's Avatar
    09-14-2014, 10:38 PM
    Off or full-range or something higher then 150HZ
    18 replies | 416 view(s)
  • MLA's Avatar
    09-14-2014, 10:12 PM
    The access door on the KXM amp is held closed by two allen head screws. Just for chits and giggles, change the position of the sub input button....
    18 replies | 416 view(s)
  • MLA's Avatar
    09-14-2014, 08:43 AM
    Is this regarding your amp, or the pic of Jason's amp? For the amp pictured above, Input Level = Hi/Low is to se the amp depending on the source...
    18 replies | 416 view(s)
  • MLA's Avatar
    09-13-2014, 06:12 PM
    Ok, so the sub level knob turns the sub up and down, its just that when all the way, its output is still lacking. That sub absolutely will...
    18 replies | 416 view(s)
  • MLA's Avatar
    09-11-2014, 01:25 AM
    MLA replied to a thread bags not emptying in Service & Repair
    Are these being manually filled and drained with a W709 pump kit, piggy backed on to the factory setup, did they replace a hard tank that was in the...
    4 replies | 143 view(s)
  • MLA's Avatar
    09-09-2014, 03:35 PM
    Ok, its safe to say that the system was not tuned with knob in mind. Just to make sure every thing is working like it should, turn the sub knob all...
    18 replies | 416 view(s)
  • MLA's Avatar
    09-09-2014, 02:33 PM
    Jason, You said you attached the bass level knob. What it supplied with the boat, and just not plugged up? What sub is there?
    18 replies | 416 view(s)
  • MLA's Avatar
    09-08-2014, 12:28 PM
    MLA replied to a thread tower cans question in Audio & Electrical
    One thing to consider with a product like a Dynamat, is reducing the volume of an already small pod. This reduces the mid-bass.
    4 replies | 164 view(s)
  • MLA's Avatar
    09-07-2014, 08:36 PM
    MLA replied to a thread Ballast Winterization in Service & Repair
    If all you have is soft bags, including the IBS, with quick disconnects, theres not much left to do. Run some Marine/RV pink antifreeze where you...
    5 replies | 202 view(s)
  • MLA's Avatar
    09-07-2014, 04:32 PM
    MLA replied to a thread interesting on new LSV in General Chat
    There has been a single pipe FAE for Tige since they went to PCM in 09. Clears the TAPS plate, no problem.
    7 replies | 240 view(s)
  • MLA's Avatar
    09-06-2014, 08:18 AM
    MLA replied to a thread Hull warranty question in General Chat
    Without reading the documentation from SC specifically regarding the Flow, I cant say specifically. My comments are general about owners doing work....
    14 replies | 377 view(s)
  • MLA's Avatar
    09-05-2014, 09:18 PM
    MLA replied to a thread Hull warranty question in General Chat
    A franchise Dealer can void a warranty just a quick as an owner can. Warranty is backed by manufacturer, not dealer. Dealer just agrees to do work at...
    14 replies | 377 view(s)
  • MLA's Avatar
    09-05-2014, 08:58 PM
    MLA replied to a thread Electrical whine in Audio & Electrical
    Ok, so the main gain is fixed, but the noise is when the EQ is in either main or AUX modes? That puts it on the output side and would make sense if...
    19 replies | 442 view(s)
  • MLA's Avatar
    09-05-2014, 08:32 PM
    MLA replied to a thread Electrical whine in Audio & Electrical
    Does the EQ have adjustable input sensitivity? If so, how is it and the amp gains set? Higher the gains, the more the system is open to unwanted...
    19 replies | 442 view(s)
  • MLA's Avatar
    09-04-2014, 07:30 PM
    Never sold/installed one, but the couple i have heard, both self powered and non-powered, and they are kinda a 1-note wonder subs in terms of SQ. If...
    10 replies | 281 view(s)
  • MLA's Avatar
    09-04-2014, 07:57 AM
    MLA replied to a thread Electrical whine in Audio & Electrical
    Boon, You easily bypass the head-unit and trigger the amps on directly. Use the red switched 12 that triggers the head-unit now, to trigger your...
    19 replies | 442 view(s)
  • MLA's Avatar
    09-01-2014, 11:50 AM
    Besides consulting the manufacturer on whats a safe cleaner to use, I have had great success with Dura-Gloss #541 Marine & RV Mildew Buster.
    10 replies | 388 view(s)
  • MLA's Avatar
    09-01-2014, 09:04 AM
    MLA replied to a thread Electrical whine in Audio & Electrical
    Give us some additional details about the system. Try running RCA direct from head-unit to sub amp.
    19 replies | 442 view(s)
  • MLA's Avatar
    08-31-2014, 10:20 AM
    MLA replied to a thread Major Audio Issues in Audio & Electrical
    Sam, It certainly sounds like you have a few issues, one compounding on another. Any failed or defective OEM installed components would need to be...
    5 replies | 236 view(s)
  • MLA's Avatar
    08-30-2014, 08:41 AM
    If the wear is fairly even left and right and inboard to outboard, then i would look upstream to the main lines and coupler. Make sure the short hose...
    16 replies | 299 view(s)
  • MLA's Avatar
    08-29-2014, 08:17 PM
    Do you have a pic of the outboard pad? Mainly interested in its thickness compared to the inboard pad. Also, how does the suspect sides pad thickness...
    16 replies | 299 view(s)
  • MLA's Avatar
    08-28-2014, 08:29 PM
    Nothing factory about 3 batteries. But, it could be the original configuration with a 2nd house battery wired in parallel. Bu then again, could be...
    11 replies | 247 view(s)
  • MLA's Avatar
    08-28-2014, 05:56 PM
    It should start in all 3 positions.
    11 replies | 247 view(s)
  • MLA's Avatar
    08-28-2014, 04:19 PM
    MNichols, If your setup consists of just the manual dual battery switch, then it is 100% manually controlled by the operator. There is nothing...
    11 replies | 247 view(s)
  • MLA's Avatar
    08-27-2014, 10:15 PM
    MLA replied to a thread Checking the grounding in General Chat
    If it happens again, jiggle the shifter to make sure its fully locked in neutral. Its real easy to not have the shifter in neutral and then shut the...
    13 replies | 235 view(s)
More Activity
About MLA

Basic Information

Age
45
About MLA
Location:
Lake Wylie NC Area
Occupation:
Marine Audio and Ballast

Statistics


Total Posts
Total Posts
773
Posts Per Day
0.54
General Information
Last Activity
Yesterday 11:44 PM
Join Date
10-27-2010
Referrals
0

1 Friend

  1. slipperyrockTKE300 slipperyrockTKE300 is offline

    Senior Member

    slipperyrockTKE300
Showing Friends 1 to 1 of 1