Squeezing my hull together to close the floor crack.
The black part under the steering wheel is where I put in a dogbone shaped piece across the crack to hold it together fiberglassed...
Type: Posts; User: Crittr
Search: Search took 0.01 seconds.
07-11-2014, 10:19 AM
07-10-2014, 01:31 PM
I drilled the holes in the transom stringer, next to nothing came out, but the flotation is totally saturated on the right side. I rigged up the shop vac to fit into the 1/2" hole and...
Hey jay dub,
Sorry for butting into your thread. From all the research I've done the only way to dry out the saturated flotation is to open up the floor and dry it out, or replace it. Vacuuming it...
The moomba rep I've been emailing, John Buescher, told me I could drill a 1/2 inch hole in the stringer where it meets the transom and crank the front of the boat up as high as possible, the...
07-09-2014, 08:23 AM
So, the moomba rep got back to me about trapped water. He said I could drill a 1/2" hole through the stringer where it meets the transom and the water would weep out of there into the bilge. I'll...
I am going through a similar problem with my 02 outback. After months of chasing the listing problem by trying to fix the brass under the boat, I have discovered a huge crack along the...
07-08-2014, 01:50 PM
Thanks, I can't see it being weaker than the glue moomba used
07-08-2014, 09:10 AM
There was a fairly big oops on the right front just under the rub rail, right about where the box beam stringer (? I don't know what you call it) runs up the side of the hull. I repaired the gel...
07-07-2014, 02:41 PM
Last week, I read about trapped water possibly causing listing. I don't have a ski locker, so I was looking around for a place to drill a hole in the floor to check that possibility out. I found a...
07-07-2014, 02:25 PM
Well.... to keep the boat level at speed, three people, two in the spotter's seat and one up front on the left.
06-25-2014, 01:27 PM
Laser sighting no, eyeball sighting. When I reinstalled them, I clamped them both between two pieces of 2X4, they look very straight. However, I will check tonight to ensure that they are...
06-25-2014, 01:08 PM
Also, should the prop be to the left or right of the rudder?
06-25-2014, 01:05 PM
Ok, so I put it all back together and finally got it on the water. I had my rudder pressed straight, new strut, shaft is straight and true. I put the tracking fins back on they are very straight. ...
I'm looking at putting a very simple system in my 2002 Outback. With all the underwater brass I'm replacing this year, simple is all we can do right now. We don't care about blasting the lake, and...
Thanks guys, we've decided that we would like to have a vdrive if we upgrade from the outback
Thanks guys, I think we've decided that if we upgrade from the outback, we will go with a vdrive and something newer.
The price sure caught my eye though....
I found an 01 mobius today for 11500.
It looks to be in great condition, but has 1500 wakeboarding hours on it.
Factory tower, wakeplate, new steering cable, any damaged upholstery has been...
I found this möbius today for $11500. I spoke with the owner, the interior is immaculate, some of it has been re-upholstered. Carpets are good, general wear and tear on the fibreglass, but no...
04-15-2014, 10:55 AM
Thanks for Responding guys,
I received a PM from John Buescher, Customer service at Skier's Choice. He indicated that the alignment of the engine due to the strut and the bent rudder are most...
04-15-2014, 10:17 AM
Yes, I've learned that it is supposed to be offset, it was however quite bent towards the port side with a significant bend halfway down to the left as well.
The tracking fins are not bent, it's...
04-14-2014, 11:09 AM
Thank you for replying, I spoke with my local dealer and they say the alignment of the mounting locations for rudder and strut are normal. I'm sure the new strut will help with engine alignment. ...
04-13-2014, 11:41 AM
View from under the boat, you can see that the holes are drilled squarely, but the fin is way off.
Holes offset in fin
04-13-2014, 11:07 AM
This is my first post, I have read everything concerning this problem and more on the forum. I am hoping that you can help with some advice, or if nothing else confirming that I'm not way...
Results 1 to 23 of 23