Type: Posts; User: gurt
Search: Search took 0.01 seconds.
I sell this prop because I would like the ACME 2079. The lake is about 400m altitude and when we are 10 or more pepole onboard with full ballasts (~3500lbs), it looks that a prop with less pitch...
I sell my propeller ACME 1235 4 Blade 14.5" x 14.25" Propeller
I use this propeller only last year, like new, in perfect condition.
10-15-2013, 09:25 AM
I will grease the impellers with Motul Tech Grease 300 (Multipurpose grease, formulated with synthetic base oil stocks and from complex lithium soap, with extreme-pressure, anti-wear, anti-oxidation...
10-14-2013, 09:35 AM
I think this will be the way I will do to winterize my Mojo :
Winterization part 1 (at the lake)
Put the boat on the trailer
Clean the hull
Empty the ballasts
Put the fuel stabilizer
10-11-2013, 08:25 AM
Hi, after reading your posts, I think I found the solution that I will use. First I will drain (block, manifold, etc) and then fill with antifreeze with this method :...
Here is a pic of yesterday :D Cloudy day but with a professional photographer on an other boat :
10-04-2013, 08:44 AM
One other question : why most of the people change the oil before winterization ? An engine specialist told me that it is much better to not let a brand new oil in the block all the winter long. For...
10-04-2013, 08:10 AM
Thank you MLA, about antifreeze that's what I thought. About fogging and more, I have informations on the engine user manual and this forum !
10-04-2013, 05:53 AM
Hello, I just read that post http://www.moomba.com/msgboard/showthread.php?9877-Winterization-Procedure-with-pics-by-Al about winterizing (thanks to Al)
My concern is about antifreeze in the block...
That's right !! That's why my center hard + IBS are full when only 60% is displayed !! In fact, my tank never drain... But I don't understand where you want to put an other valve...
Hy, no I didn't glue the fittings. I just tighten by hand but it spin also. The fittings on the stock ballast were glued by the ex-owner. I will glue them I think because water flows by the vent when...
trmaggie98, I'm sure you will enjoy with these ballast !! But You will probably change the prop due to extra weight...
For my 2012 mojo the stock prop was 14.25" x 14.5" and the ACME 1235 is a 14.5"...
Hy, I have some pictures of my ballast installation (same setup as wolfeman)
Here is a maybe better picture of the Boshworth valve :
The ACME 1235 is the prop I'm looking for. The guy from wakeprop suggest me the ACME 2079 for my mojo with that ballast config.
I'm afraid about top speed with that 14.5" x 12" prop
after replacing the prop, did you have to calibrate something because speed at same rpm change or is there a sensor that doesn't depend from prop?
Hello Wolfman, thks for infos. So your prop comes from moomba? I saw some prop from wakeprop.com
Did you remember the model that you have? thx
I don't have issue but it looks that an other prop...
Hi, just installed the new ballast today. For the 1" TH I have to enlarge the stock holes (didn't take tool to do it). We tested (only 1 driving and 1 surfing). Speed was 15km/h (9.4 mph) max...
Hi ! Received my order but I wasn't at home. I can pick it up at the post office on monday (2x1100lbs, 370lbs and IBS).
I will install it on Thursday :D
Cool ! Do I have to enlarge the existing hole in the hull ?
I checked everything and my order is placed ;) (I took some TH 1" in case I have to replace the stock one's) and hope I forgot nothing ! (I always took one extra items of each except the bags...
Ok, thanks for info (it seems to be logic to have the same section everywhere). So my schematic is correct ?
The TH off the boat are ok for the 1" or do I have to replace them ?
Maybe the hose between the 370 vent and the left 1100 can be 1" because it's used to fill ?
ok, I didn't know about this championship. I posted a picture (it as to be checked by moderator) of your ballast setup that I've done (like yours) but a bit more detailed (to be sure that I...
Pope guard haha funny! you forgot watchmaker. I work for swiss air navigation services as a technical supervisor (something like FAA in the U.S)
Results 1 to 25 of 31