Search:

Type: Posts; User: Young24

Search: Search took 0.01 seconds.

  1. Replies
    21
    Views
    1,153

    Update, my problems came back so I took the carb...

    Update, my problems came back so I took the carb off and checked the float bowls for flaking as I read that Holley had problems with the 2006 4150 carb and mine matched the serial numbers. I called...
  2. Replies
    21
    Views
    1,153

    I just took the caps off the air mix screws and...

    I just took the caps off the air mix screws and turned the screws all the way in. Then I backed them out a half turn at a time. The idle went up as I turned them out so I had to adjust that also. The...
  3. Replies
    21
    Views
    1,153

    How do you clean the pilot jet? Do I need to...

    How do you clean the pilot jet? Do I need to bring it in to do this or can a novice do it? I don't know much about carbs, but if it's an easy thing to do I will give it a try. I'm 2 hours from a...
  4. Replies
    21
    Views
    1,153

    I've been reading a lot of posts about taking the...

    I've been reading a lot of posts about taking the caps off the screws on the carb and adjusting them? Others seem to have success curing similar problems to mine by adjusting the scews. It sounds...
  5. Replies
    21
    Views
    1,153

    Ok, I changed all the plugs, had a hard time...

    Ok, I changed all the plugs, had a hard time starting it (it would stall when i choked it) took it out for about an hour of surfing and it ran great. After an hour it started stalling when idling and...
  6. Replies
    21
    Views
    1,153

    Thanks for your input, the boat runs really good...

    Thanks for your input, the boat runs really good at all rpm's it only struggles on the hole shot and some times while idling. I'll take the plugs out and check/replace them.
  7. Replies
    21
    Views
    1,153

    Yes the electric choke seems to work fine. The...

    Yes the electric choke seems to work fine. The boat will start after I open the throttle all the way and then put it back in neutral. It will warm up and run great, but after awhile on the lake it...
  8. Replies
    21
    Views
    1,153

    I ran a tank with seafoam through it and it...

    I ran a tank with seafoam through it and it wasn't much better. How do you check the electric choke. I am planning on new plugs next.
  9. Replies
    21
    Views
    1,153

    Ok, I finally replaced the fuel filter, but it...

    Ok, I finally replaced the fuel filter, but it still stalls and idles rough? What do I do next?
  10. Replies
    21
    Views
    1,153

    Mine has a carb, I followed the fuel line on...

    Mine has a carb, I followed the fuel line on passenger side, but couldn't see it. I haven't taken the lockers apart yet
    Though.
  11. Replies
    21
    Views
    1,153

    06 obv running rough

    I just traded my 02 outback dd for an 06 obv with 23 hours on it. It's like new but it has a rough idle and
    Stalls on hole shot. I've tried carb cleaner and seafoam in the gas but problem persists....
  12. Replies
    15
    Views
    2,277

    Oil drain hose

    I cut the hose drained the oil and put the brass bolt in it with a cap along with a clamp. Other than 3 trips to the hardware store to get the right size, it was easy.
    Thanks for your help,
    Young
  13. Replies
    15
    Views
    2,277

    Deerfield I like your idea. Do you think the one...

    Deerfield I like your idea. Do you think the one that goes inside the hose will hold? Is there pressure on the oil drain hose that might push that loose?

    Appreciate the help,
    Young
  14. Replies
    15
    Views
    2,277

    That's what I thought I would need to do. I'll...

    That's what I thought I would need to do. I'll start with the extractor, but I would still like to replace the brass cap if possible. I assume I need to wait unti the next oil change to cut the hose?...
  15. Replies
    15
    Views
    2,277

    Can't get oil drain nut off

    I changed my oil, but in the process I stripped the crap out of the connector on the end of the drain hose. The nut would not come off and I had to use channel lock pliers because it just spun. I...
Results 1 to 15 of 15