Search:

Type: Posts; User: mcdye

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    9
    Views
    196

    a few options, 1- mount the speakers on the up...

    a few options,
    1- mount the speakers on the up rights, run wire around the bow for the starboard side.
    2- drill a hole in the port upright to jump over to the cross bar, entering the factory hole...
  2. Replies
    9
    Views
    287

    @mbusch5, curious do you have the tower fold...

    @mbusch5, curious do you have the tower fold assist?

    I ran mine up the port side. Removed the grommet, then used a long drill bit at a angle and made a hole to the port upright. The tower...
  3. Replies
    370
    Views
    54,271

    good one.....

    good one.....
  4. Replies
    6
    Views
    401

    If you can not locate a letter. This might be an...

    If you can not locate a letter. This might be an option, if it is not damaged bad, you could PlastiDip all the letters so they would match. Very easy to do on the larger letters. I did the chrome...
  5. Thread: Speaker Mount

    by mcdye
    Replies
    7
    Views
    392

    You had to go there :) Joe hit it right, with...

    You had to go there :)

    Joe hit it right, with no hole in the port side upright of the OZ and OZHD tower most will drill a hole on the outside to jump over to the factory gromment hole, with more...
  6. Thread: touch-up paint

    by mcdye
    Replies
    4
    Views
    361

    Your girlfriend/wifes finger nail polish is what...

    Your girlfriend/wifes finger nail polish is what most use.
  7. Replies
    6
    Views
    411

    They are used for shipping the boats with the...

    They are used for shipping the boats with the tower down and the plastic cover. You can find them in the dealer burn pile. They are handy for lowering your tower to get in/out of a garage.
  8. Replies
    27
    Views
    1,111

    Locally dealer finally got one. Sure I will at...

    Locally dealer finally got one. Sure I will at least seat in it at the boat show... http://www.xtrememarineinc.com/pre_owned_detail.asp?veh=3910304&nv=y
  9. Replies
    14
    Views
    614

    we only use the tower for WB, WS, KB and...

    we only use the tower for WB, WS, KB and Surfing.... everything else hooked to the ski pylon.
  10. Replies
    5
    Views
    334

    Thanks Rick. It does say 2.5 but it is the '15...

    Thanks Rick.

    It does say 2.5 but it is the '15 classic scheme and with new colors.
  11. I have never seen that before... I am with Boone,...

    I have never seen that before... I am with Boone, must be a addon afterwards.
  12. Replies
    1
    Views
    150

    That is it. When the boats come of the the mold,...

    That is it. When the boats come of the the mold, they cut all the holes via jigs where or not they are used.
  13. Replies
    9
    Views
    616

    Re: What's the deal with the new Mojo Magic?

    15 Mojo's. They are already shipping and sellling. Climbed all around in one last weekend, dealer sold it this week.

    Sent from my MB860 using Tapatalk 2
  14. Replies
    6
    Views
    529

    $20 - paypal/shipped to lower 48. They have...

    $20 - paypal/shipped to lower 48. They have never been used, new would cost $28/+shipping.
  15. Replies
    6
    Views
    529

    bags are sold, fittings are still available.

    bags are sold, fittings are still available.
  16. Replies
    13
    Views
    716

    I gather you have the Remote mount. I am with...

    I gather you have the Remote mount. I am with you on this one, there has been times where I had to take off the remote house, place it in a vise, and use a pipe wrench on the filter.....
  17. Replies
    17
    Views
    1,039

    Are you sure it is coming up OR is the two parts...

    Are you sure it is coming up OR is the two parts seperating? I had one that started to seperate creating a bubble. Took pictures, contacted SeaDek and it was warranty replaced.
  18. Thread: 2015 lsv

    by mcdye
    Replies
    8
    Views
    1,701

    Congrats on the new boat!!

    Congrats on the new boat!!
  19. Replies
    6
    Views
    529

    Willing to sell separate. This is a plugNplay if...

    Willing to sell separate. This is a plugNplay if you have 1" fitting which I believe started in '12
  20. I tried the Velcro way, did not work for me, it...

    I tried the Velcro way, did not work for me, it would come loose, did not want to staple or glue down. Thought about straps similar to the '14 setup, but sold the boat before doing.
  21. Replies
    3
    Views
    224

    Where ever you can get it to fit under the cover...

    Where ever you can get it to fit under the cover between the fresh water inlet and the vdrive inlet. Just find a place to splice it in using Straight and or 90 degree fittings. The last one I got...
  22. Sorry to hear about that. I was always leery of...

    Sorry to hear about that. I was always leery of loosing one on my '10 LSV. We took that one and the one behind the driver seat and put them in the rear locker for the road trip.
  23. Replies
    6
    Views
    529

    2 x Fly High Pro 1100 NIB w/ Valves

    2 x Fly High Pro 1100 NIB w/ Valves (1", W743) PlugnPlay for newer boats
    $320, Shipped to lower 48.
  24. Replies
    27
    Views
    1,009

    Sounds like you are getting older, wiser, and...

    Sounds like you are getting older, wiser, and realizing you have got to go to work the next day. :)

    Learning tricks, we slow down the boat and load up the side for the approach. Bring the rope in...
  25. Thread: Cover Straps

    by mcdye
    Replies
    13
    Views
    781

    yep that is how i did mine as well. The rear...

    yep that is how i did mine as well. The rear pole I put on the floor thou.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4