Search:

Type: Posts; User: Wake Master

Page 1 of 7 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    26
    Views
    1,655

    We are in southwest Michigan he does ride in The...

    We are in southwest Michigan he does ride in The INT league tri state Indiana, Ohio, Michigan.
  2. Replies
    26
    Views
    1,655

    13912 This is my sons engagement photo. He is...

    13912

    This is my sons engagement photo. He is riding at 85 feet, 24.5 MPH and almost 3000# of ballast. The wake is huge.
  3. Replies
    26
    Views
    1,655

    You should also check to see if the speed is...

    You should also check to see if the speed is accurate with a GPS. This can also have an impact on the wake.
  4. Replies
    26
    Views
    1,655

    I would have the wakeplate at 1/2 or a little...

    I would have the wakeplate at 1/2 or a little less, This will ramp the wake more like the 210
  5. Replies
    26
    Views
    1,655

    Ballast is only one factor. You must also look at...

    Ballast is only one factor. You must also look at Speed, Distance, Wake Plate Position, & the weight of the passengers. All factor into getting the desired results. We have an 07 XLV with 1150# in...
  6. Replies
    24
    Views
    923

    The CWB Marius is a great board it is wider and...

    The CWB Marius is a great board it is wider and has soft landings. I purchased this board from Evogear in December for $295. Keep an eye on their discounts they change weekly. This is an...
  7. Thread: OJ Props

    by Wake Master
    Replies
    25
    Views
    1,363

    I had the same problem with an OJ 07 wakeboard...

    I had the same problem with an OJ 07 wakeboard prop. One blade came off without hitting anything. I was lucky no damage to the boat. When you look close at the prop where it broke you can see flux...
  8. Replies
    10
    Views
    854

    Not sure what the nut size is I use a large...

    Not sure what the nut size is I use a large cresent wrench. The thread is standard. You can use a block of wood to wedge the prop then loosen the bolt. Leave the nut on at the end when you use the...
  9. Replies
    4
    Views
    437

    This is in Ultimate Wakes July Newsletter ...

    This is in Ultimate Wakes July Newsletter


    4th Annual Supra Moomba Reunion
    The event will be held August 7th from 9am until 5pm at the Fox River Preserve Marina. Launch, slip for the day and...
  10. The best advice is to tell people it is like your...

    The best advice is to tell people it is like your sitting on the ground and someone is trying to help pull you up. You must point your toes down and let your but slide toward your heals.

    Sounds...
  11. The 2 important parts of engine break in are the...

    The 2 important parts of engine break in are the number of engine cycles (Hot to Cold) and changing engine speeds. These 2 factors will help everything seat. More is better. You should also have the...
  12. Replies
    5
    Views
    605

    I change the trans fluid every season. You can...

    I change the trans fluid every season. You can pump the oil out with a pump like the link below. I make sure I measure what I remove so I do not overfill. You should be able to pump out 2 quarts....
  13. Replies
    14
    Views
    1,227

    This is the information from an older post by...

    This is the information from an older post by Engine Nut

    A little clarification. The issue we have been seeing that is presumed to vapor lock is a condition that appears to be most prevalent on...
  14. Replies
    6
    Views
    734

    Here is a CWB bag ...

    Here is a CWB bag

    http://boardersmall.com/xcart/product.php?productid=22315&cat=305&page=1
  15. Replies
    14
    Views
    1,607

    The question you need to ask is why is the fluid...

    The question you need to ask is why is the fluid low? You may need to look for a leak if it is low again.
  16. Replies
    14
    Views
    1,607

    In regards to the chech engine light. The only...

    In regards to the chech engine light. The only way to determine the code it is throwing is to have the dealer read the ECM with the software. If it happenes each year does it have something to do...
  17. Replies
    57
    Views
    5,570

    This is the setup on our 07 XLV 340HP 750 in...

    This is the setup on our 07 XLV 340HP

    750 in each of the rear compartments
    1100 in the center
    150 under each of the front seats

    The wake is great.
  18. Replies
    22
    Views
    2,312

    If you click the word "service" on the K&N web...

    If you click the word "service" on the K&N web site for the Marine filters this is there explaination of service.

    K&N Air Filter Cleaning Instructions


    1. APPLY CLEANER

    FOLLOW ALL SAFETY...
  19. Replies
    22
    Views
    2,312

    If you have a newer EFI engine more than likley...

    If you have a newer EFI engine more than likley you have a K&N filter. You should get the K&N recharge kit. It contains a solvent to clean the filter and an Oil spray to recharge the filter.
  20. Replies
    14
    Views
    947

    You need at least 15 feet of water below the boat...

    You need at least 15 feet of water below the boat to have the wake fully develop.
  21. Replies
    9
    Views
    653

    The engines do have knock sensors so even if you...

    The engines do have knock sensors so even if you had to run 87 octane in a crunch it would not be a problem. You may loose a little performance. You are better off to use fresh 87 octane than old 89...
  22. Replies
    20
    Views
    4,875

    It is located at the front of the engine (rear of...

    It is located at the front of the engine (rear of the boat) it is mounted in front of the crankshaft. First purchase a new impeller and gasket. Remove the three screws on the front cover. Turn the...
  23. Replies
    8
    Views
    597

    If you have a filter on the ballast system simply...

    If you have a filter on the ballast system simply unscrew the filter, empty the water, put the filter back on, turn on the pump and they will fill.
  24. Replies
    8
    Views
    975

    Reese It was good meeting you. The event Boaters...

    Reese
    It was good meeting you. The event Boaters choice put one was well done. You did a good job keeping things organized as the dock starter.
  25. Have you checked the Fuel Pump or for water in...

    Have you checked the Fuel Pump or for water in the tank? When you rebuilt the carb did the float look corrored this is a sign of water in the tank.
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4