Search:

Type: Posts; User: jstenger

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    16
    Views
    404

    Center tank leaking

    I am the guy that replaced my tank. You will have to remove your fuel tank to get the tank partially out. You will have to either cut it up or pull the v-drive to get it all the way out. The tank...
  2. Solving the ballast breaker switch problem

    You will need a meter that measures inrush current. Basically the current required to start the pumps. It will be higher than the 12amp continuous current.
  3. Replies
    11
    Views
    352

    Have you tried using a voltmeter? Start at the...

    Have you tried using a voltmeter? Start at the battery circuit breaker and work your way across to the switches.
  4. Replies
    126
    Views
    12,700

    Ghetto gates-post your pictures here

    Found the perfect spot for my getto gate.

    http://i1217.photobucket.com/albums/dd382/Joestenger/20160618_164720.jpg

    Fits perfect in the wakeboard rack.
  5. Replies
    9
    Views
    498

    Just a heads up if you already didn't know, but...

    Just a heads up if you already didn't know, but it has been said before on here that sometimes the tanks are hard to get completely full. The vent is very slow, and the back pressure will cause the...
  6. Replies
    1
    Views
    114

    Check the connection to the gauge first, then...

    Check the connection to the gauge first, then pull the floor to check the connection at the sending unit.
  7. Replies
    2
    Views
    126

    It may be an inline fuse right next to the...

    It may be an inline fuse right next to the battery.
  8. Replies
    24
    Views
    1,377

    You are way too light in the bow.

    You are way too light in the bow.
  9. Ballast bag/wakeplate not working - fuse location?

    This is exactly what I told you to do in post #15.
  10. Replies
    23
    Views
    1,023

    Driver seat riser?

    The seat just slips over the post. It is a snug fit, but it lifts straight up. Just make sure your swivel is loose.
  11. Ballast bag/wakeplate not working - fuse location?

    Yes, both the plate and pumps are controlled by that module.
  12. Are your pumps still in the factory position in...

    Are your pumps still in the factory position in the rear lockers? If so, then they probably had to remove/replace when they added the Autoflow upper brackets. Take the passenger side rear cover off...
  13. Replies
    103
    Views
    27,256

    Sticky: Same here. No room for the torque wrench. Just...

    Same here. No room for the torque wrench. Just used open end wrenches.
  14. Replies
    20
    Views
    1,382

    Yes it would.

    Yes it would.
  15. Mondo stereo make over, have some questions (battery and wiring)

    Here is how I ran mine. RCA's and speaker wires go thru holes underneith amps. Power wires on top and around. Amps have 3/4" spacers.
    ...
  16. Replies
    20
    Views
    1,382

    MLA does have a good point.

    MLA does have a good point.
  17. Factory IBS Install/plumb process - 2013 Mojo?

    I think you mean port side, since there is already a hole on the starboard side that the current hard tank vent goes thru. And the answer is yes. Just remove the black air vent that goes into the...
  18. Factory IBS Install/plumb process - 2013 Mojo?

    The factory setup IS piggy backed. It uses two lines, whereas Wakemaker's uses one line. The theory behind the second line is that it gives the hard tank a second way of venting when draining.
  19. Factory IBS Install/plumb process - 2013 Mojo?

    Check out the following thread starting with post 191.

    http://www.moomba.com/msgboard/showthread.php?t=26912

    Wakemakers only uses one fill/drain line in their IBS kit. The factory uses two...
  20. No need to fuse the 1/0 inline wire.

    No need to fuse the 1/0 inline wire.
  21. Replies
    282
    Views
    10,966

    2016 Craz owners.

    I, like others on here, have moved the pumps to a different location. I put all three of mine on the plastic piece behind the engine. Others mounted them on the inside of the engine divider panels.
    ...
  22. Replies
    282
    Views
    10,966

    2016 Craz owners.

    Just hit the empty button again. It will run for around 30 seconds and shut off.
  23. Anyone seen or tried Ronix Wakesurf Shaper on Moomba boats

    Can you post the EBAY link?
  24. Are you going to fill it with spray foam?

    Are you going to fill it with spray foam?
  25. Replies
    4
    Views
    617

    IBS plus Hard Tank. Possible solution.

    DO NOT add any checkvalves of any kind to an IBS hard tank combination.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4