Search:

Type: Posts; User: Jayrodau

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    45
    Views
    3,292

    Re-upholstery cost?

    Who did your monogram stitching where it says SUPRA?
  2. 2011 Moomba Mobius LSV FOR SALE in Hunstville, Decatur, AL areas

    I live in the same area but in Madison. We go to smith lake in Cullman mainly. Where do y'all go out at? Why you selling such a nice boat?
  3. Replies
    1
    Views
    243

    Rear vents for blower/exhaust

    Does anyone know where i can buy different ones than the stock black plastic ones. When people climb back in boat water can go through them and sometimes ive had surf waves back fill into them. I was...
  4. Sticky: Instructions on replacing moomba steering cable

    Yes, great write up! I'm so glad it finally became a sticky! Very helpful a d informative. I also spoke with JesseC and he went through everything with me also.
  5. Sticky: Instructions on replacing moomba steering cable

    The teleflex SSC15418 is the correct model number cable for my 2005 moomba lsv. As far as the install: Yes, A guy on the forum I talked with sent me this and figured I would share. I have been...
  6. Replies
    5
    Views
    455

    Steering Cable for 05 LSV

    Yes, I will message you everything.
  7. Replies
    4
    Views
    396

    2006 moomba outback dieing

    Few things...
    1. Might be fuel filter
    2. Might try marine grade stabil next fill up with ethanol free gas if possible.
    3. Is it over heating? Temp gauge readings.
    4. Vapor lock or cheap ethanol...
  8. Replies
    41
    Views
    3,266

    Quick and cheap mod!

    Sweet...I assume you have to replace the bulbs from behind the gauges? Looks good!
  9. Replies
    6
    Views
    368

    I wish it was that simple.

    I wish it was that simple.
  10. Replies
    6
    Views
    368

    Cable that attaches to the PP servo. Have you...

    Cable that attaches to the PP servo. Have you done this before?
  11. Replies
    6
    Views
    368

    Perfect Pass cable

    My perfect pass servo motor needs replacing, but I also want to replace the cable attached to it. I'm guess this is the throttle cable? How hard is it to replace the cable? Want to ask before I...
  12. Replies
    96
    Views
    5,575

    Dude...that Upholstery job is awesome! They did a...

    Dude...that Upholstery job is awesome! They did a great job and the Moomba on the back bench looks amazing!
    Did you have a reference for the Bentley's Upholstery shop or did you just shop around....
  13. Replies
    4
    Views
    376

    I just ordered a new Johnson Water pump. After...

    I just ordered a new Johnson Water pump. After researching online it seems impossible to replace the back seal without the proper tools/press.
  14. Replies
    4
    Views
    376

    I am talking about the rear seal, not the seal on...

    I am talking about the rear seal, not the seal on the front cover plate. Mine is leaking in the back of the water pump not at front where the impeller is installed
  15. Replies
    4
    Views
    376

    Impeller leaking in the rear

    Has anyone replaced their rear seal on the Johnson raw water pump on an Indmar? Mine is leaking and getting the belt wet at times and causing it to squeal for a moment.

    I think this is the part I...
  16. Replies
    10
    Views
    562

    Perfect pass help!

    It's your raw servo motor. I called and talked to perfect pass....very helpful. I bet if you do the servo motor test it won't tighten your cable. It's $139 for a new one. My wife won't let me order...
  17. Thread: Laces

    by Jayrodau
    Replies
    3
    Views
    242

    Laces

    Is there any good aftermarket locking laces out there that anyone recommends? I know some ppl just put regular shoe laces in their bindings. I need to replace mine from normal wear.
  18. Replies
    6
    Views
    358

    My boat is 45min away in storage. Maybe someone...

    My boat is 45min away in storage. Maybe someone with this Gravity 3 strainer setup could go out and measure the gasket/o-ring and post up the size. That would be awesome!
  19. Replies
    6
    Views
    358

    ballast water strainer (gravity 3)

    Does anyone know the size of the strainer gasket size on the Gravity 3 valve tree on my 05 LSV?
    Curious if I can just buy a new gasket seal online somewhere instead of ordering the whole kit from my...
  20. Replies
    2
    Views
    407

    cool video....Some nice Jumps! Look very...

    cool video....Some nice Jumps! Look very comfortable with the board. How much ballast you running while wakeboarding?
  21. Replies
    6
    Views
    419

    07 outback direct drive taking on water

    Can you post a pic of it please?
  22. Replies
    10
    Views
    562

    Perfect pass help!

    I'm gonna do the servo motor test. It's gonna be hard for me to call them if they are only open M-F. We usually don't get on the water until Friday evening around 5:30 and out on the water all day...
  23. Replies
    10
    Views
    562

    Perfect pass help!

    It turns on fine....I can set the mph and the display seems to work just fine. It just keeps accelerating past the set mph. I've tried resetting it but no luck. Any other suggestions? I think...
  24. Replies
    10
    Views
    562

    Perfect pass help!

    Here's a pic of the module under the dash also.
    17495
  25. Replies
    10
    Views
    562

    Perfect pass help!

    We tried using our prefect pass today and had no luck. We set it to different mph and none seem to work. Here are some pics. Does anyone know things I can try or see anything wrong? I don't really...
Results 1 to 25 of 52
Page 1 of 3 1 2 3