Search:

Type: Posts; User: maxpower220

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    5
    Views
    282

    A common issue. You can use JB weld, or take the...

    A common issue. You can use JB weld, or take the muffler out and put on a few layers of fiberglass and fix it like new.
  2. Replies
    13
    Views
    556

    Remember that new carpet is "fluffy" and tends to...

    Remember that new carpet is "fluffy" and tends to fill any gap. Unless you really are looking for things like that, it would be easy to miss. Older carpet mats down. Replace the carpet, and your...
  3. Replies
    4
    Views
    146

    Sliding.com can get you a good par number for the...

    Sliding.com can get you a good par number for the cable. They may have input on the overall issue. There are a few connections that allow the cable to move the rudder without binding. Those may...
  4. I have a "boat" slalom ski, a Connelly Pilot. It...

    I have a "boat" slalom ski, a Connelly Pilot. It is a super big slalom ski with a shape. It is almost as big as a wakeboard. However, it is amazingly easy to get up on. It allows the skier to ski...
  5. Replies
    242
    Views
    12,524

    First 10 laps of GP were great.

    First 10 laps of GP were great.
  6. Replies
    4
    Views
    154

    I had to replace my ignition switch on my 08. It...

    I had to replace my ignition switch on my 08. It developed a blank spot that affected starting. You may be starting that issue.
  7. Not a lot cheaper, but contact Max at skier to...

    Not a lot cheaper, but contact Max at skier to skier. He was the "best" price that I found. His knowledge of skiing and the product are very good. He may offer a group rate if you go to him with a...
  8. Replies
    5
    Views
    311

    Freebirds for lunch.

    Freebirds for lunch.
  9. Replies
    6
    Views
    234

    Check skiertoskier.com . They stock and sell OJ...

    Check skiertoskier.com . They stock and sell OJ props, free shipping, and in total the lowest price I've seen on the internet. If you prefer Acme, look at skidim.com and use the coupon code. They...
  10. Thread: Bed Liners

    by maxpower220
    Replies
    14
    Views
    470

    My f150 came with a drop in liner. I wouldn't...

    My f150 came with a drop in liner. I wouldn't have purchased it, but it keeps the bed nice. I tried a di y product in the past. It looked nice for a while, but did not hold up. Newer products may...
  11. Replies
    28
    Views
    1,116

    What's wrong Drew?

    What's wrong Drew?
  12. Is that schedule 40? I hope that your prototype...

    Is that schedule 40? I hope that your prototype is to fab up some different type of material. Exhaust is hot, just like your heat gun.

    Second, I would (at a minimum) change the name you refer...
  13. Replies
    28
    Views
    1,116

    Your Indmar Owner's Manual has specifications...

    Your Indmar Owner's Manual has specifications that an oil should meet at a minimum. Get ANY oil that meets that minimum spec and you are fine. There are laws that protect you as long as you meet...
  14. Replies
    22
    Views
    718

    The 3.7 isn't an ecoboost, it regular non turbo....

    The 3.7 isn't an ecoboost, it regular non turbo. Not sure how good or bad it would tow. The 3.5 ecoboost is a beast.
  15. Replies
    1
    Views
    100

    Check the ground to the battery, to the motor,...

    Check the ground to the battery, to the motor, and to the gauge. If you can, try to find a mechanical oil gauge and use it to determine actual pressure.

    Cold oil will usually send a higher...
  16. I owned a 2008 Outback and a 99 Malibu. You...

    I owned a 2008 Outback and a 99 Malibu. You didn't give the hours on the Bu, but if it has less than 400 hrs on it, the Bu will have a better ski wake. Later down the road, the Bu will probably...
  17. Fake a lake is cheap. Get one and an impeller. ...

    Fake a lake is cheap. Get one and an impeller. Do a test in your yard. Cracked head or block or gasket can still run perfect, for a while.

    Run a test on the trailer, don't rev the engine on a...
  18. It is easy to remove the heads from the boat...

    It is easy to remove the heads from the boat while the engine is still in the boat. Put down a lot of towels on the carpet, because it can be a mess.

    Take lots of close up pictures of the head...
  19. Take starter to an electrical rebuild shop and...

    Take starter to an electrical rebuild shop and have them look at it. I had a similar issue, cost $30 to repair.
  20. I would guess that a log or something got caught...

    I would guess that a log or something got caught on the prop and then struck the hull causing all of the damage.

    I'm not a dealer, but if that is THE brochure boat, I would not have water tested...
  21. Replies
    6
    Views
    405

    To be sure, you would need to use a mechanical...

    To be sure, you would need to use a mechanical gauge. I would venture to say that you oil pressure isn't truly at 80, the accuracy of the gauges could be questionable. I would only start to get...
  22. Replies
    11
    Views
    469

    If your kit comes with a mounting product, it...

    If your kit comes with a mounting product, it will be 2 part, 5 minute epoxy. That is the product that manufacturers will use if you order it through them. Other product can/will work, you have to...
  23. Replies
    4
    Views
    310

    If you are going to use it a lot, I recommend...

    If you are going to use it a lot, I recommend getting whips Then use the top edging and vertical bumpers you referred to.

    I had a lift where the boat was most of the time and lined the dock...
  24. Replies
    6
    Views
    314

    Pull the impeller out. Crank up for a few...

    Pull the impeller out. Crank up for a few seconds and see if you still have the noise. That will narrow down/out the impeller.
  25. Replies
    6
    Views
    314

    I assume that you can tell that it is coming from...

    I assume that you can tell that it is coming from the front of the engine. My first guesses would be the water pump bearing. Followed by the impeller shaft, followed by the impeller itself. Do...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4