Search:

Type: Posts; User: 98Roo

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    454

    Have you verified you're getting fuel all the...

    Have you verified you're getting fuel all the time? Crack the fuel line going to carb, jump the two wire oil pressure sensor and the pump will run with key in run position. I had the 3 wire sensor...
  2. Replies
    10
    Views
    695

    I had a bunch of people in my boat one day last...

    I had a bunch of people in my boat one day last year and a bunch of pink/orange spots showed up and nothing will take them out. This was on new reupholstered seats. Everything I have read on these...
  3. Replies
    6
    Views
    212

    I found the problem right after I posted. I...

    I found the problem right after I posted. I traced a couple of purple wires that are supposed to go to a kill switch. Trace your purple wires, one is power from key switch and runs to a terminal to...
  4. Replies
    6
    Views
    212

    Start but wont stay running..

    I have installed a set a gauges/switches from a newer boat (around an '03 or so I believe) into my '98 Outback and I'm having an issue where the engine will start but will not stay running unless I...
  5. Replies
    23
    Views
    2,251

    I use the DA polisher from Shurhold with their...

    I use the DA polisher from Shurhold with their polish. You need a hi-speed buffer with speed adjustments to polish the gel coat with compound.
  6. Replies
    23
    Views
    2,251

    Nice boat! I got my hi speed buffer for like $40...

    Nice boat! I got my hi speed buffer for like $40 at harbor freight and picked up some wool pads from Oreilly Autoparts.
    This vid is great! https://www.youtube.com/watch?v=ke5kfYz9Ybw
  7. Replies
    61
    Views
    4,901

    I have a New Dimension Tower being built right...

    I have a New Dimension Tower being built right now. Black tower, black bimini, black board rack, lighted ski tow.
    Replace all gauges except speedos for now. (Will probably go with perfectpass...
  8. Replies
    12
    Views
    1,876

    Oh that sucks, sounds like you certainly had some...

    Oh that sucks, sounds like you certainly had some other issue with the carb. I'll have to remember that if I ever decide to replace my carb. Seems like if the Holley didn't need it then neither would...
  9. Replies
    12
    Views
    1,876

    For the record, to properly adjust the mixture...

    For the record, to properly adjust the mixture screws you need a vacuum gauge. I just had mine rebuilt and used the gauge to set my mixture for maximum vacuum and it runs great. You also want the...
  10. Replies
    3
    Views
    408

    I plan on replacing all the gauges this winter...

    I plan on replacing all the gauges this winter but my original Faria gauge seems to work fine. I called skidim and talked to thier service manager and he told me to send the switch back and he'll...
  11. Replies
    5
    Views
    423

    Go ahead and do what I did and buy the kit from...

    Go ahead and do what I did and buy the kit from Great Lakes Skipper for a Cobalt 196. It is everything you need and is way cheaper than pieceing it together....
  12. Replies
    3
    Views
    408

    Fuel Pressure Cutoff Switch

    This switch was bad when I bought my boat and the PO had just bypassed it with a jumper to let the fuel pump run when ignition is on. This switch just cuts off the fuel pump when oil pressure is too...
  13. Replies
    5
    Views
    423

    http://www.boatersland.com/tay1166.html

    http://www.boatersland.com/tay1166.html
  14. Replies
    102
    Views
    9,987

    Thank you! She is very fun to drive and...

    Thank you!

    She is very fun to drive and pretty quick! Over the winter im going to add a tower so I can actually accommodate more people when towing someone.

    It was super easy to install. I...
  15. Thread: New Interior

    by 98Roo
    Replies
    12
    Views
    1,194

    Nice! The lady that did my interior said the...

    Nice! The lady that did my interior said the drivers bucket at the two back curved panels were the biggest pain in the butt to do. I finally just took the whole boat to her to get the back panels...
  16. Replies
    102
    Views
    9,987

    Thank you! It's been a lot of work but it's...

    Thank you! It's been a lot of work but it's paying off on the weekends now! I ordered the pad directly from SeaDek. Just call and you'll talk to Susan. I think the pad drawing they used was for a...
  17. Replies
    102
    Views
    9,987

    http://i64.photobucket.com/albums/h192/redej8/IMG_...

    http://i64.photobucket.com/albums/h192/redej8/IMG_3237.jpg
    http://i64.photobucket.com/albums/h192/redej8/IMG_3238.jpg
  18. Replies
    102
    Views
    9,987

    Just a small update. Finally got my SeaDek...

    Just a small update. Finally got my SeaDek platform pad. Color is storm grey over black. I love it!
    http://i64.photobucket.com/albums/h192/redej8/IMG_3231.jpg...
  19. Replies
    102
    Views
    9,987

    Haha! Thanks! That's our "old dock" that needs to...

    Haha! Thanks! That's our "old dock" that needs to be redecked and apparently the bench needs redecking too haha!
  20. Replies
    102
    Views
    9,987

    Thanks! Here's a couple more pics of the boat...

    Thanks!

    Here's a couple more pics of the boat in the water.. Still waiting on Seadek to make my platform pad....
    http://i64.photobucket.com/albums/h192/redej8/IMG_0538.jpg...
  21. Replies
    102
    Views
    9,987

    Here are some final updates probably until I...

    Here are some final updates probably until I decide which tower I am going to buy and install.
    I had an issue where the exhaust hose wouldn't seal to the exhaust tips and had water leaking into the...
  22. Wish I could've made it to this!

    Wish I could've made it to this!
  23. Replies
    58
    Views
    2,419

    Yea you could do that but I would not run one for...

    Yea you could do that but I would not run one for a while. They're sealed to keep sparks out of bilge.
  24. Replies
    58
    Views
    2,419

    You need a marine starter. There is a difference...

    You need a marine starter. There is a difference between marine and automotive starters and alternators. Check around online too. I know skidim and bakes sells them too.
  25. Replies
    1
    Views
    168

    Wow, I didn't think that was really possible....

    Wow, I didn't think that was really possible. TaylorMade would probably be it unless you can find a junked boat somewhere which is very unlikely.
Results 1 to 25 of 81
Page 1 of 4 1 2 3 4