Search:

Type: Posts; User: papou

Page 1 of 6 1 2 3 4

Search: Search took 0.04 seconds.

  1. Thread: Ballast pump

    by papou
    Replies
    4
    Views
    102

    Well I'm on three years , ill order 3 new...

    Well I'm on three years , ill order 3 new impellers .
  2. Thread: Ballast pump

    by papou
    Replies
    4
    Views
    102

    Ballast pump

    How long does the Jabsco ballast pump impeller last ?
    I don't have a problem just wondering if I should have spares
  3. Replies
    7
    Views
    204

    Mine doesn't fold any further than yours .

    Mine doesn't fold any further than yours .
  4. Thread: 2015 models...

    by papou
    Replies
    198
    Views
    9,569

    Will the 6.2 be closed loop cooling & have cats ?...

    Will the 6.2 be closed loop cooling & have cats ?
    I see this being a very costly engine for the end user in the long run ��
  5. Replies
    4
    Views
    152

    Your fuel pump isn't keeping the pressure up ,...

    Your fuel pump isn't keeping the pressure up , when it's running the boat is using the fuel and pump can't supply enough.
    When the engine is not running and you put the key in the on position the...
  6. Thread: 2015 models...

    by papou
    Replies
    198
    Views
    9,569

    I don't know witch company it is but I've heard...

    I don't know witch company it is but I've heard that theres a surf boat in development wich the company is testing a new drive system kind of like the Volvo pods, but that will retract or tilt or???
  7. Replies
    7
    Views
    205

    There's a 2013 LSV that comes to our lake on...

    There's a 2013 LSV that comes to our lake on weekends, and he has changed his exhaust hose 3 times in 50 hours . His engine is catalyzed ,maybe something to do with more heat in exhaust from the cat...
  8. Replies
    1
    Views
    67

    Two philips screws with large washers that pass...

    Two philips screws with large washers that pass through the two 1inch holes in the fiberglass , that screw into the plastic panel which may be broken .
  9. Thread: Transom LEDs

    by papou
    Replies
    25
    Views
    1,304

    Mine came from same seller ( gaowenv ) on ebay ....

    Mine came from same seller ( gaowenv ) on ebay . 2 years and counting all is good .
  10. Thread: FAE & OJ Prop

    by papou
    Replies
    5
    Views
    222

    FAE & OJ Prop

    Installed the FAE this week amazing difference , except for the more noticeable growl of the prop. Can this be fixed or do I need to get an Acme propeller , Im using the OJ TZ-X5 what does ACME have...
  11. Thread: operating temp?

    by papou
    Replies
    12
    Views
    308

    I didn't mean the strainer cup ,i meant the...

    I didn't mean the strainer cup ,i meant the threaded input and output fittings, they should be sealed and not twist or the pump will pull air in , giving you a high temp reading , heater not working...
  12. Thread: operating temp?

    by papou
    Replies
    12
    Views
    308

    Do you have a strainer ? If so be sure the...

    Do you have a strainer ? If so be sure the threaded fitting are sealed and do not twist ,the pump will pull air in and cause this issue , i had this problem on my 05 LS
  13. Replies
    50
    Views
    2,059

    I ordered mine a week prior to this thread would...

    I ordered mine a week prior to this thread would that count ?, i did mention this forum .I've only received 1 of 2 boxes so far one box is somewhere between Chicago IL and the planet .
  14. Replies
    25
    Views
    595

    Im using the OJ TZ-X5 ,nice and strong out of the...

    Im using the OJ TZ-X5 ,nice and strong out of the hole lost 5 mph and it's also quite musicale.
  15. Replies
    8
    Views
    264

    Why am i useing the wrong oil ? Its a 40...

    Why am i useing the wrong oil ? Its a 40 viscosity (high temp) the W is winter or "W" grade so 5 will flow better at startup COLD then 15 . Have you ever tryed to drain your oil cold ? Very slow and...
  16. Replies
    8
    Views
    264

    I'll usually add 1/2 a litre of oil every 25...

    I'll usually add 1/2 a litre of oil every 25 hours , using full synthetic 5w40
  17. Replies
    5
    Views
    239

    Do you have any play in the wheel ? The bushing...

    Do you have any play in the wheel ? The bushing behind the gear that drives the cable could be worn out ( hopping gears)
    Just a thought ,I've replaced my steering shaft because it was worn .
  18. Replies
    140
    Views
    9,137

    2014 April Picture Thread.

    Nice :) you guys are lucky to have fun on the water I'm still stuck with 3.5 feet of ice. http://img.tapatalk.com/d/14/04/20/nabyqupu.jpg
  19. Replies
    5
    Views
    246

    Did you check the comp with all the plugs removed...

    Did you check the comp with all the plugs removed so the engine cranks freely ?
  20. Thread: strange noise

    by papou
    Replies
    12
    Views
    644

    It sounds like a lifter ,pushrod,taping the...

    It sounds like a lifter ,pushrod,taping the rocker arm , removing the covers inspecting and reinstalling I would do if its coming from the top end.
  21. Replies
    4
    Views
    234

    If it's your dock why not use Mooring whips,your...

    If it's your dock why not use Mooring whips,your boat will never touch the dock . I've used them for two years before I got a lift ,bumpers will scuff the hull in long periods of time .
  22. Replies
    328
    Views
    25,305

    Isn't the Flow suppose to work with the stock...

    Isn't the Flow suppose to work with the stock ballast, and keep the boat more level when surfing? I don't think it was designed for overweighted boats . Moomba's intention was to creat a better wave...
  23. Replies
    15
    Views
    777

    Another theory is it will be re vined and...

    Another theory is it will be re vined and detailed as so its not recognizable the trailer will be registered as a home built then it might be sold across the country like in Ontario or Quebec .
  24. Replies
    16
    Views
    745

    I got mine from heatercraft,300 series two hot...

    I got mine from heatercraft,300 series two hot tubes and one vent , plumbing is easy to install the heater was tricky under the dash behind the panel . Sorry i dont have pics anymore i only needed a...
  25. Replies
    28
    Views
    1,925

    New Mondo arrived!

    Black & green ,sexy
Results 1 to 25 of 129
Page 1 of 6 1 2 3 4