Search:

Type: Posts; User: Jayrodau

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. I went through this last year and replaced mine....

    I went through this last year and replaced mine. I used to know where to order the triangle plug from but I cant remember at the moment. I redid mine and shrink wrapped all the new wiring with my...
  2. Replies
    28
    Views
    659

    They want $600 (ACME 1235) + $360 (Shaft) + Labor...

    They want $600 (ACME 1235) + $360 (Shaft) + Labor $300

    I dont have anything to cut the old shaft off with. So I am leaning towards letting them do it. Plus, replacing the shaft seems difficult....
  3. Replies
    28
    Views
    659

    You were correct. They just called and said they...

    You were correct. They just called and said they want to cut the shaft off to remove it. I will need a new shaft and new prop. So looks like im down for the weekend. They have to order a shaft.
  4. Replies
    28
    Views
    659

    Damaged prop?!? How Bad?

    So they can't get my prop removed. They have broke 2 prop pullers and used heat no luck. Saying they are going to have to pull the shaft!!!! OMG I'm sick right now.
  5. Replies
    28
    Views
    659

    By the way my stock prop was a OJ 1280 4 Blade...

    By the way my stock prop was a OJ 1280 4 Blade 14" x 18" and I am replacing with a NEW ACME 1235 4 Blade 14.5" x 14.25".

    Hope I can tell a difference!
  6. Replies
    28
    Views
    659

    I totally agree! Way cheaper make your own kit! I...

    I totally agree! Way cheaper make your own kit! I am going to send my damaged in to hopefully get repaired. Even though its go some pretty harsh dings I hope they can so the repair!
  7. Replies
    7
    Views
    204

    vdrive oil question

    I think mine is starting to leak somewhere. It seems to be lower on the Walter dip stick after each trip. :( Any suggestions? I asked my mechanic he said possibly a loose/cracked hose.
  8. Replies
    28
    Views
    659

    Damaged prop?!? How Bad?

    Dropped it off this morning and that getting a new prop was under a 30min install. The guys couldn't get it loose with their prop puller clamp. So I ended up leaving it. The said they were going to...
  9. Replies
    7
    Views
    204

    vdrive oil question

    How are yall putting oil into the vdrive? Through the walter dip stick hole?
  10. Replies
    6
    Views
    141

    WTB a 4 blade prop in good condition.

    Please PM me if you have one available. Thanks!
  11. Replies
    28
    Views
    659

    Think I can use it this weekend with it like...

    Think I can use it this weekend with it like that? Looks like most of the repair shops are backed up from the 4th. I don't really want to spend $600 on a new prop.
  12. Replies
    28
    Views
    659

    Damaged prop?!? How Bad?

    My prop hit the side of my trailer when pulling up on the trailer in the water. Wind was blowing hard back of boat drifted over my back left board. Should I get it replaced? Can this prop be...
  13. Replies
    1
    Views
    67

    Side dash panel mount help

    My side dash panel came loose and I cannot figure out how to get it remounted?!? I have attached some pictures. Any suggestions would be great! ...
  14. Replies
    46
    Views
    4,172

    Re-upholstery cost?

    Who did your monogram stitching where it says SUPRA?
  15. 2011 Moomba Mobius LSV FOR SALE in Hunstville, Decatur, AL areas

    I live in the same area but in Madison. We go to smith lake in Cullman mainly. Where do y'all go out at? Why you selling such a nice boat?
  16. Replies
    1
    Views
    272

    Rear vents for blower/exhaust

    Does anyone know where i can buy different ones than the stock black plastic ones. When people climb back in boat water can go through them and sometimes ive had surf waves back fill into them. I was...
  17. Sticky: Instructions on replacing moomba steering cable

    Yes, great write up! I'm so glad it finally became a sticky! Very helpful a d informative. I also spoke with JesseC and he went through everything with me also.
  18. Sticky: Instructions on replacing moomba steering cable

    The teleflex SSC15418 is the correct model number cable for my 2005 moomba lsv. As far as the install: Yes, A guy on the forum I talked with sent me this and figured I would share. I have been...
  19. Replies
    5
    Views
    504

    Steering Cable for 05 LSV

    Yes, I will message you everything.
  20. Replies
    4
    Views
    448

    2006 moomba outback dieing

    Few things...
    1. Might be fuel filter
    2. Might try marine grade stabil next fill up with ethanol free gas if possible.
    3. Is it over heating? Temp gauge readings.
    4. Vapor lock or cheap ethanol...
  21. Replies
    41
    Views
    3,724

    Quick and cheap mod!

    Sweet...I assume you have to replace the bulbs from behind the gauges? Looks good!
  22. Replies
    6
    Views
    425

    I wish it was that simple.

    I wish it was that simple.
  23. Replies
    6
    Views
    425

    Cable that attaches to the PP servo. Have you...

    Cable that attaches to the PP servo. Have you done this before?
  24. Replies
    6
    Views
    425

    Perfect Pass cable

    My perfect pass servo motor needs replacing, but I also want to replace the cable attached to it. I'm guess this is the throttle cable? How hard is it to replace the cable? Want to ask before I...
  25. Replies
    96
    Views
    6,342

    Dude...that Upholstery job is awesome! They did a...

    Dude...that Upholstery job is awesome! They did a great job and the Moomba on the back bench looks amazing!
    Did you have a reference for the Bentley's Upholstery shop or did you just shop around....
Results 1 to 25 of 65
Page 1 of 3 1 2 3