Results 1 to 10 of 14

Hybrid View

  1. #1
    Join Date
    Jun 2008
    Location
    Eugene OR
    Posts
    1,706

    Default Moving amps Install in plexyglass?

    I am in the process of moving my amps so i can place them all together and out of the way of gear. I am looking to have them all on the same plexyglass back board so i can limit the amount of screw holes into the boat.

    My question is if plexyglass the right way to go or is there something else i should be using? I will have three amps installed on it.
    2008 Outback V
    “Do not wait; the time will never be “just right.” Start where you stand, and work with whatever tools you may have at your command, and better tools will be found as you go along." -Napoleon Hill

  2. #2
    Join Date
    May 2009
    Location
    Carlton Oregon
    Posts
    6,029

    Default

    Plexi is great Mike, just make sure its 1/2 inch thick so it doesn't wobble with the weight on there. Plexi also can be painted, back side and you can have some cool looking stuff on it.
    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    Exile ZLD
    6 SX65M Cabins
    6 XM9 Towers
    1 XI Big 15 Woofer in a custom Fiberglass box
    1 XI 1K Harpoon
    2 XI 800.4
    1 XI 2500.1
    2 Interstate 2400U 6V Golf Cart Batterties
    Custom 1 Off Evolution Cover

  3. #3
    Join Date
    Apr 2008
    Location
    California
    Posts
    2,840

    Default

    Jester it all depends on what you use and how & where you plan on attaching it to. I used composite Alucobond which is less than 1/8" thick but extremely rigid but light. One thing to remember is that when you attach the amps to the board you automatically increase the rigidity of the amp board as the amps are now a structural member. Look at mine below, i attached to the floor reinforcing rib on bottom and the rubrail reinforcing block up top. This thing does not move at all yet keeps it out of the way. I do plan on making a guard of some sort to keep things off the amps so the airflow/cooling insn't affected.
    Attached Images Attached Images
    2007 Mobius LSV

  4. #4
    Join Date
    Oct 2009
    Location
    Pacific NW USA
    Posts
    506

    Default skip the plexi

    Jester - There are a lot of good choices on what to mount your amplifiers to but my feeling is, I'd skip the Plexi. Yes sure, Mike is right you can use it and it will work fine. If show quality is your primary goal, then I wont rain on that parade. You can paint it, edge light it etc... but its not so fun to drill and tap each hole when using plex. Its not fun when you crack it because your template is off a bit either.

    I'd suggest looking at the HDPE boards that come in a variety of thicknesses (I think mike just bought one for his boat). I also like the PVC expanded foam product that is becoming more cost effective. Lastly, I've seen guys build great racks from metal by welding a skeleton together, then powdercoat it and then mount to it.

    Lots of choices out there. Since your down in Eugene area, check out TAP plastics. I think they have a local branch down there.

    Cheers,

    -Brian
    Exile Audio

  5. #5
    Join Date
    May 2009
    Location
    Carlton Oregon
    Posts
    6,029

    Default

    Hey Razz can i trouble you to measure how fare your screw locations are from the bottom to the top? I know where the bottom edge rail is but im having a bit of a time being certain i have the upper rail to screw into. Both areas are an invh thick right? I was thinking screwing 1/2 inch into it to mount my racks.
    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    Exile ZLD
    6 SX65M Cabins
    6 XM9 Towers
    1 XI Big 15 Woofer in a custom Fiberglass box
    1 XI 1K Harpoon
    2 XI 800.4
    1 XI 2500.1
    2 Interstate 2400U 6V Golf Cart Batterties
    Custom 1 Off Evolution Cover

  6. #6
    Join Date
    Jan 2010
    Location
    Austin, Texas
    Posts
    63

    Default

    Hey Jester,

    I'm in this same process as you. I uninstalled all the amps, radio, battery...etc last weekend from the boat. Last owner of the boat mounted amps on particle board, wires running every where, and he did not seal the board so it was a soggy stinky mess. I swear that boards weigh must have 100lbs with all the water in it.

    I'm going to create new amp racks, install dual batteries with BlueSea add a battery kit, and I also bought a new head unit because the cheap one in the boat didn't allow for iPod/iPhone hook up. I think I'm going to try and install one battery on each side of the bow underneath the front cushions. Only 10 inches underneath the seats so I'm probably going to have to go with those Optima battery's since you can mount them in any position. They are so expensive though.

    I searched homedepot, lowes, and couple of other hardware stores but didn't find any large sheets of plastic board. Someone mentioned using cheap cutting board from walmart but I didn't find anything that is big enough for my amps. Plexiglass would be cool but as someone else mentioned, it cracks easy when drilling so I'm not going that route.

    I think I'm going to just by some 1/2 plywood and seal it with some roll-on truck bed coating/liner like Rust-Oleum from Walmart for $43 buck a gallon. Nothing fancy since I'm just going to cover it up with carpet. I found a Local carpet shop and they sell marine carpet 3x72 for $50 bucks. Looks like I should be able to do this for under $150 bucks. I'll start my own thread once I get started this Friday.

    So many great ideas from people on this forum. Thanks to every one who has posted pictures and/or made suggestions in all the different threads !!!
    Last edited by ausbill32; 02-22-2010 at 05:48 PM.
    2007 Moomba LSV

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •