well no point in posting pictures......... my platform broke off just the same as the brackets in the earlier posts. They are at the welders right now getting fixed. poor design by moomba, why are the brackets not made out of stainless steel, then you would have no problems.
Did we get an answer on how to tighten the bracket attached to the boat?? I could not figure it out! Again bad design!!!
Results 81 to 86 of 86
-
09-06-2011, 12:17 PM #81
Senior Member
- Join Date
- Apr 2010
- Location
- saskatchewan, canada
- Posts
- 277
2005 Mobius LSV
Gravity IV (750s rear, 400 mid and 650 bow)
wakeplate, perfect pass,
Not sure what stereo I have, but I have 3 amps 2 subs 6 x 6.5 mids and tweets and 4 tower speakers ( 2 x 8 inch and 2 x 6.5 and tweets)
Fuel Injected
1433 acme prop
-
09-06-2011, 12:35 PM #82
Senior Member
- Join Date
- Aug 2008
- Location
- Cottage Grove, MN
- Posts
- 696
did the bracket on the transom break, or the bracket on the platform? Also, are you saying that when tightening the bottom bolts on the transom brackets that you can't get them to tighten? The top bolts should be accessible from inside the boat, you might have to pull the carpet back from the wall of the transom.
Originally Posted by saskie99
2006 Outback V - Gone
2008 LSV - Gone
2013 other brand
-
09-06-2011, 12:41 PM #83
Senior Member
- Join Date
- Apr 2010
- Location
- saskatchewan, canada
- Posts
- 277
The bracket on the swim platform broke just like in the pictures, when i took it off I noticed the boat bracket was a little loose so I tried to tighten it and the screws just turn. I didnt realize that you can get at them from the inside of the boat, I thought they were glassed in.
2005 Mobius LSV
Gravity IV (750s rear, 400 mid and 650 bow)
wakeplate, perfect pass,
Not sure what stereo I have, but I have 3 amps 2 subs 6 x 6.5 mids and tweets and 4 tower speakers ( 2 x 8 inch and 2 x 6.5 and tweets)
Fuel Injected
1433 acme prop
-
09-06-2011, 01:32 PM #84
Senior Member
- Join Date
- Aug 2008
- Location
- Cottage Grove, MN
- Posts
- 696
on my boat, only the top bolts are accessible, the bottom bolts are below the level of the floor. Originally Posted by saskie99
2006 Outback V - Gone
2008 LSV - Gone
2013 other brand
-
09-06-2011, 01:37 PM #85
Senior Member
- Join Date
- Apr 2010
- Location
- saskatchewan, canada
- Posts
- 277
Do they just have a nut on them? I sure hope I can get at them!
Anybody out there have a 05 lsv and had to tighten the bolts on the swim platform boat bracket???2005 Mobius LSV
Gravity IV (750s rear, 400 mid and 650 bow)
wakeplate, perfect pass,
Not sure what stereo I have, but I have 3 amps 2 subs 6 x 6.5 mids and tweets and 4 tower speakers ( 2 x 8 inch and 2 x 6.5 and tweets)
Fuel Injected
1433 acme prop
-
09-06-2011, 02:02 PM #86
Senior Member
- Join Date
- Aug 2008
- Location
- Cottage Grove, MN
- Posts
- 696
yes, the ones that are accessible have a fender washer and a nyloc on them. Originally Posted by saskie99
2006 Outback V - Gone
2008 LSV - Gone
2013 other brand
Reply With Quote