Page 1 of 5 123 ... LastLast
Results 1 to 10 of 43
  1. #1
    Join Date
    May 2009
    Location
    Carlton Oregon
    Posts
    5,962

    Default Bracing your V Drive locker for 1100 Fat Sacs

    I received a couple emails on how did i brace my V Drive locker for my 1100 fat sacs.

    Parts needed are all from Home Depot

    4 3/4 x 48inch x 1/8th long aluminum angle bars. http://www.homedepot.com/h_d1/N-5yc1...atalogId=10053
    6 1 inch Lag Stainless Steel Lag bolts
    8 Stainless Steel bolts
    8 Stainless Steel Machine screws
    8 Stainless Steel washers
    8 Stainless Steel lock washers

    All the above can be substuted for what ever size you want. I persoanly used 24x10 i think it was.

    I used 2 48 inch peaces as the bottom rail and used 3 lag bolts to attach that to the floor of the boat.
    I then used the 2 other 48inch peases for my upward bracing. Front is apx 22inch high and the rear is apx 21 inch high.
    I then bolts the upper braces to the lower angle bracket and then again to the upper cross member in the boat.
    Make sure you watch for the locking tabs on the plastic doors. As you can see in my pic i mis measured by 1/2 inch and need to fix that now lol.
    Also you will notice the engine actualy doesnt sit centered in the engine bay so pay attention to this when you place your upward braces.

    This all cost me about 35 bucks. and 2 hours or 4 beers of time.

    Passenger side bracket. Drivers looks the same.


    1100 Empty

    1100 Full on goofy side. You can see where my brace is blocking my panel hinge. That will be fixed ASAP.
    I also need to repostion the 1100 bags slightly to allow them to sit a bit more upright.



    I will post some video of the surf wave after this next weekend as we are still dialing it back in. I can say this with the 1050 nose ballast i run made a huge improvment wave is now even larger and the pocket is insainely long.
    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    Exile ZLD
    6 SX65M Cabins
    6 XM9 Towers
    1 XI Big 15 Woofer in a custom Fiberglass box
    1 XI 1K Harpoon
    2 XI 800.4
    1 XI 2500.1
    2 Interstate 2400U 6V Golf Cart Batterties
    Custom 1 Off Evolution Cover

  2. #2
    Join Date
    Dec 2006
    Location
    Tigard, Oregon
    Posts
    3,016

    Default

    Nice work Mike! Looks great and cheap to boot!
    Al

    2006 Mobius LSV

  3. #3
    Join Date
    Jun 2008
    Location
    Eugene OR
    Posts
    1,683

    Default

    Mike Nice work. looks like it would cost more then just 4 beers to make.
    2008 Outback V
    Do not wait; the time will never be just right. Start where you stand, and work with whatever tools you may have at your command, and better tools will be found as you go along." -Napoleon Hill

  4. #4
    Join Date
    Aug 2008
    Location
    Cottage Grove, MN
    Posts
    735

    Default

    Awesome! Thanks for posting this. What size lag screws did you use to go into the floor? You list 1", but what diameter?
    2006 Outback V - Gone
    2008 LSV - Gone
    2013 other brand

  5. #5
    Join Date
    May 2009
    Location
    Carlton Oregon
    Posts
    5,962

    Default

    Quote Originally Posted by mnpracing View Post
    Awesome! Thanks for posting this. What size lag screws did you use to go into the floor? You list 1", but what diameter?
    I want to say they were 3/8th course thread. I didnt look at diameter as much as length i wanted them to be long enough to bite but not so long they would go into the floor and runners so deep.
    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    Exile ZLD
    6 SX65M Cabins
    6 XM9 Towers
    1 XI Big 15 Woofer in a custom Fiberglass box
    1 XI 1K Harpoon
    2 XI 800.4
    1 XI 2500.1
    2 Interstate 2400U 6V Golf Cart Batterties
    Custom 1 Off Evolution Cover

  6. #6
    Join Date
    Jun 2009
    Location
    Sunnyvale, CA
    Posts
    229

    Default

    Hey Mike. Thanks for the "How To". I had decided not to do it since my exhaust was so close to the v-drive door and have never had it push past the brace. However since you make it look so easy I think I will be running to Home Depot later.
    2008 MOBIUS LSV - Acme 1847, GIII w/1100lbs Vdrive, IBS, PPSG, Wake plate, Z-5, Kenwood 700U, Kenwood Kca-RC107MR , Exile SXT65, Kicker 700.5, Kicker 350.4, Polk MM651, JL 13.5 Thin-Line Sub.

  7. #7
    Join Date
    Jul 2011
    Location
    Rapid City, SD
    Posts
    89

    Default

    Well done. Is this something that all of us should consider with bigger bags in the vdrive lockers? I have a 2x3 aluminum brace at a diagonal from high bow side to low transom side. Is that enough?
    2013 Tige RZR w/ConvexVX, WetSounds Rev10s, 6x650s, Syn4 and Syn6 amps.
    Surf Quiver 4x Brigade Wakesurfing Surf Boards- Aviator, Zulu, .352 Special, Bomber
    Victoria Skim 2xGremlins, 2x Agents, 1 Factor, 1 Pixie Bri Chmel Pro Model

  8. #8
    Join Date
    Sep 2010
    Location
    Lake wallenpaupack PA
    Posts
    846

    Default

    Quote Originally Posted by zroutt View Post
    Well done. Is this something that all of us should consider with bigger bags in the vdrive lockers? I have a 2x3 aluminum brace at a diagonal from high bow side to low transom side. Is that enough?
    Plenty........

  9. #9
    Join Date
    Aug 2010
    Location
    Nokomis, Saskatchewan
    Posts
    559

    Default

    thats what i was wondering to.. that is a huge brace and i couldn't see how a bag could push past that? So i'm assuming that when they changed the hull design in 06 they changed that as well as my 05 has that angle bracket.

    Geoff
    2014 Mondo on the way.... can't wait!!

  10. #10
    Join Date
    Jan 2008
    Location
    Tallahassee, FL
    Posts
    11,054

    Default

    Nice job documenting this for everyone, Mike! You're all set for the big shindig now, right?
    My Mom said I'm not allowed to get wet!
    2008 LSV
    2000 Outback LS (sold)
    Exile Tunes
    PWI
    LLTR!!!!!!!!



Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •