nice work mmobius i have been reading this as your been posting and had to keep refreshing to make sure you were done before i posted LOL. I like this idea and i will be doing it soon as my port side pad is walking out again.
Results 11 to 20 of 26
Thread: DIY: Tower Pad Swap Out
08-25-2011, 11:47 PM #11Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
6 SX65M Cabins
6 XM9 Towers
1 XI Big 15 Woofer in a custom Fiberglass box
1 XI 1K Harpoon
2 XI 800.4
1 XI 2500.1
2 Interstate 2400U 6V Golf Cart Batterties
Custom 1 Off Evolution Cover
08-26-2011, 12:31 AM #12
Good Job! Thanks for the DIY. I don't need to replace mine yet, but I am glad to know where to look for info when i do.2008 MOBIUS LSV - Acme 1847, GIII w/1100lbs Vdrive, IBS, PPSG, Wake plate, Z-5, Kenwood 700U, Kenwood Kca-RC107MR , Exile SXT65, Kicker 700.5, Kicker 350.4, Polk MM651, JL 13.5 Thin-Line Sub.
08-26-2011, 02:45 PM #13
I was told by a someone that a lot of manufacturers are not even using the pads anymore?David
2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM7, Exile SXT65Q, Exile XI12D, Exile Harpoon, Exile SM600.1 , Exile Xi800.4.
05-09-2012, 11:24 PM #14
Mmobius thanks for writing this up. Just did it the other night and it was very quick/easy to do thanks to your information.
Much appreciated!2008 Mobius LSV
07-10-2012, 04:47 PM #152004 Outback Blue/white w/5.7 indmar 350, Direct Drive
Rockford fasgate cabins
Rockford fasgate 500w amp (cabin) and a kenwood HU (kmr700u)
Polk 10in sub (2)
Polk P330 amp (subs)
07-12-2012, 03:55 PM #16
Can this also be used on the XLV? I need to replace my pads and do not want to wait on ordering if I can just go to Wal-Mart!!! Please let me know if anyone has used these on an XLV2008 Mobius XLV, Z5 Rack, RockFord Fosgate Amps and 12" Rockford sub, DBoot5 8" & 6" Tower speakers, Kicker Amp and 6.5" interior speakers, Inland Surf, Hyperlite, Liquid Force, Aerial Swing Away Racks, Perfect Pass StarGazer, ACME 1235 and Evolution Cover.
07-12-2012, 06:35 PM #17
I have not needed to swap out the pads but I see no reason why it would not work.
I do have the same pads on the top surface of the boat to give people a target to hit with their feet when boarding the boat.ImageUploadedByTapatalk1342128884.995260.jpg2010 Moomba XLV
Gravity 3, wake plate
1100 surf side v-locker
650 in the floor locker
400 under the surf side seat/port dash area
400 under the surf side playpen seat
600 to move around
07-17-2012, 11:17 AM #18Member
- Join Date
- Oct 2009
Good write up on the process however I posted those extact same traction pads a year or so ago & they lasted about 6 months before they started to "walk-out" like the OEM pads did. Hope yours last longer than mine.
07-30-2012, 06:05 PM #19
Thanks for the write up on this one! I noticed ours are starting to walk out on our 2010. Probably something I will tackle in the off season. I appreciate the images and the step by step.Derek & Poppy
2010 Mobius LSV Sandrock/Fossil
Gravity III ballast, wake plate, Z5
05-27-2013, 11:13 AM #20
DIY: Tower Pad Swap Out'08 Mobius LSV, Mods- 1100 lb Rear Sacs, IBS Sac, Center 400 Sac, Dedicated thru-hull intakes and pumps per sac, SeaDek One Piece Mica over Black Roo, EZ Net Cargo Nets, Swivel Drivers Seat, Hot Water Shower, Hinged Wind Block, Bow Cushion Adapter Plate for Drink Holders Access, etc, etc.