An EQ all the way because it serves multiple roles. It can shape speakers, act as a multi-zone control and much more.
The Throttle Box is a fixed notch filter and doesn't really do much for an XM9 specifically.
The XM9 built-in tweeter attenuation switch is a 1-ohm resistor on a 4-ohm tweeter so you get very little audible attenuation.
Results 41 to 50 of 71
Thread: Exile XM7 vs. XM9
09-24-2012, 11:29 AM #41
09-24-2012, 04:00 PM #42
Krak - The two are mutually exclusive. Over all flexibility would be hands down installing an EQ. Typically those are more expensive then the built in features of the Tbox or tonal switches built in the XM9's.
The switches on the XM9 effect the horn function. The speaker doesn't have a tweeter as mentioned above.
The throttle box is not a notch filter. It manipulates the phase of the horn from narrow to wide.
Both features are subtle changes at rider distance.
An EQ of any brand, would offer dramatic changes at all distances.
If you'd like more detailed info, shoot me a pm.
09-24-2012, 05:55 PM #43
Not to argue but since the above contradiction I would like to politely defend a few technical facts.
All horns have a diaphram at the base of the horn. That diaphram is either a tweeter, midrange or woofer. In this case it is a tweeter diaphram for a 'horn tweeter'. When you take the horn apart you will find a titanium dome tweeter loading into a compression chamber at the mouth of the horn. Essentially this is the same design that has been around since the late 1920s. Read my 'Anatomy of an HLCD' article.
A Double-Throw, Single Pole switch at the nose of the XM9 places a 1-ohm resistor in or out of the 'horn tweeter' circuit and when active the resistor is in series before the 2nd order highpass filter of the 4-ohm 'horn tweeter'.
The math to calculate series resistance related to attenuation is:
Take the amount of attenuation in decibles desired. Divide by 20. Convert that to it's inverse log with your scientific calculator. Multiple that times the tweeter's nominal impedance. Subtract from the answer the tweeter nominal impedance.
In this case we are looking at about 1 dB of attenuation under linear conditions. However, the tweeter impedance rises at higher frequencies thereby minimizing the attenuation. Also, the highpass passive crossover increases in impedance as you enter the crossover zone. Both conditions minimize the impact of the resistor and minimize the attenuation at the extremes of the 'horn tweeter' operation. 1 dB is considered the minimum level that the human auditory system can discern. So you may not hear much of a difference with the switch in either position. But don't go by the math. Just listen for yourself.
I think an alternate way of obtaining the 'horn tweeter' attenuation would have been to use a DPDT switch with series/parallel resistance after the passive crossover and before the 'horn tweeter' so the net impedance would be the same whether or not the resistors are in the circuit. This would have helped stabilized the 'horn tweeter' impedance and provided a more linear (equal at all frequencies) attenuation. I would probably go for a 2 to 2.5 dB of attenuation so that the effect is more noticable. Just my opinion on that. Hope this helps.
09-24-2012, 06:15 PM #44
man, nothing like a mathmatical pissing match..
how about if we all agree to disagree and move on. I'm sure the next post would be brian disproving everything david just posted.. and so on...
you guys are both experts in your field and we all know this. it was an exile thread so I believe that we should leave the answering to brian and let brian stay out of the threads asking for opinions on places to purchase non-exile gear and wetsounds'06 Supra Launch 20SSV-gone but never forgotten
09-24-2012, 06:18 PM #45Drew
New ride: 2012 Mojo
Old ride: 2008 OBV
09-24-2012, 06:51 PM #46
09-24-2012, 06:54 PM #47
He was speaking in regards to the switch on the 9 as well as the Throttle box. The decision is clear, an EQ will give you more control and allow you to fine tune.06 Supra 24 Gravity Games
09-24-2012, 07:28 PM #48
Krak - To answer your question many people don't want to take the plunge for a 200-400 eq solution in a boat. If you dont have an EQ, these are great features to have. If you do have an EQ, these are redundant things to have. Does that make sense? Sound is such a subjective thing. To much coloration /alteration can be bad. And the same goes with not enough.
I'm not at all trying to down play putting an EQ in a boat, but for many, it just adds to the complexity of the entire system which can bring noise and install headaches into the picture. From a personal point of view, I like EQ's in a boat for all the NON eq functions they typically offer. Most Eq's in this day and age have line drivers and zone controls built into them. Good stuff!
If your starting from scratch, I'd recommend going with an "EQ". It all boils down to cost versus benefit. Make sense?
Sandm - I'd agree. I dont see the point to getting into technical theory in forums. Who knows, maybe I'm wrong. I've spoke to the admins. They know my position. Nuff said.
09-24-2012, 07:33 PM #49
totally agree on the eq point if nothing more than a great zone controller. one of the comments I kept getting on the last boat was how nice it was to fade the surf hlcd's out when chillin at the dock so you don't piss off the people at the next dock, but I wish I would have added a real eq as opposed to just a fader to have the ability to balance the cabin/tower when surfing. too often the boat was too loud and no one could carry on a conversation while the surfer wanted tunes loud.
It's on my must-have list for the next install this month. hoping mike remembers my zld'06 Supra Launch 20SSV-gone but never forgotten
10-31-2012, 01:50 PM #50
I went with the ZLD and now i'm going to sell my KMR 700U headunit as it doesn't get used. I just plug my phone into the aux in port on the ZLD and rock on... so handy. I also installed a bluetooth setup as well and use that most of the time.2014 Mondo on the way.... can't wait!!