I'm a newbie and need advice.
I hit something while out on the lake caught up in a storm (very choppy) and took the boat out of the water to check the damage. Initially we felt a vibration, but didn't seem severe and passed quickly. Upon inspection we have bent the prop and it appears the strut too. That said I read a forum post about intentionally 'bent' strut bearings to ease driver swerve/pull and removal. I wondered if this was true and what year that stopped at. I have Moomba LSV 2005.
After the incident we drove for about 30 mins with no sign of any problems, but was concerned and very choppy so pulled it out of the water. I haven't put it back into the lake to try it again as I'm affraid to do more damage.
Any advise would be appreciated.
Results 1 to 9 of 9
Thread: Possible bent Strut / bearing
07-17-2013, 07:50 PM #1Junior Member
- Join Date
- Jul 2013
Possible bent Strut / bearing
07-17-2013, 09:15 PM #2
If you know the prop is bent then dont use the boat unless your trailering it, the added stress can damage the shaft seals.
Are you refering to the Strut that holds the drive shaft and the prop is bent? It takes a pretty solid hit to bend it, if its bent then you will need a new one.
Also yes on the Moomba boats the Shaft and Strut set off center to the Left of the Rudder. This stopped in 12 with the release of the Mojo. The LSV and OBV might have this also but i think the Mojo was the first to go center drive like with the rudder.
I would first get the prop fixed, then if you are not sure if anything is bent, take it for a spin, it should be smooth and no vibrations, if you have vibrations it could be the drive shaft its self is bent.Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
6 SX65M Cabins
6 XM9 Towers
1 XI Big 15 Woofer in a custom Fiberglass box
1 XI 1K Harpoon
2 XI 800.4
1 XI 2500.1
2 Interstate 2400U 6V Golf Cart Batterties
Custom 1 Off Evolution Cover
07-17-2013, 09:18 PM #3
The strut will be offset from the rudder to allow removal of the shaft. First check your alignment. That will tell you if you have bent your strut if you cannot get it aligned.09 21v LAUNCH
run your engine after you change your oil
68 th Member. WS420,HSE Revolution, OJ 466, Acme1157,1100 sacs,Kicker HLCD's n IX500.4, Supra Coolies
07-17-2013, 09:30 PM #4
if you wanna see bent ill pull up a pic of when i hit a long last summer..but like said beforeit will be off set a little for shaft removal..mine did the vibration on take off..did it after i hit the log, then stopped and took off and noticed a vibration..then did it again when i went to trailer it2004 Outback Blue/white w/5.7 indmar 350, Direct Drive
Rockford fasgate cabins
Rockford fasgate 500w amp (cabin) and a kenwood HU (kmr700u)
Polk 10in sub (2)
Polk P330 amp (subs)
07-18-2013, 01:56 AM #5
If it looks anything like this then that's BAD...
If it were me (again) I'd pull everything, have it checked, and replace as needed. Having any part of the running gear off just a little is going to cause unnecessary wear and tear on the rest. Better safe than sorry.Old enough to know better, young enough to do it anyway.
07-18-2013, 12:07 PM #6
I hit a rock going at idle and had to replace shaft, strut and prop. The boats are heavy enough that you can damage everything with a strike against anything fairly solid, even at low speed. Some shops can straighten and true your shaft but more than likely you will need to replace the strut and maybe the shaft and repair the prop. You can do it yourself and it's a great thing to learn. I can do the whole job in a couple of hours now.My Mom said I'm not allowed to get wet!
2000 Outback LS (sold)
07-18-2013, 03:50 PM #7
I have always been curious how you replace the strut. I mean, I know how you phyisically do it, but how you ensure that it is in proper alignement once you re-install it (not to mention access the nuts on the inside of boat under the oil pan). I thought I was going to have to do this several years back, and I had no idea how I was going to re-align the thing.08 LSV
Go big, or go home.