Page 3 of 3 FirstFirst 123
Results 21 to 30 of 30
  1. #21
    Join Date
    Dec 2006
    Location
    Tigard, Oregon
    Posts
    3,016

    Default

    For those with an LSV, see page 8 of the thread below for a simple solution to this issue. I put a lock washer in the gap at the top and it eliminates the rattle. This may or may not work for you depending on the size of the gap.

    http://www.moomba.com/msgboard/showt...asher+platform
    Al

    2006 Mobius LSV

  2. #22
    Join Date
    Apr 2011
    Location
    NY
    Posts
    210

    Default

    After about a year the set screws on mine ('13) are wearing dangerously close to going through the bracket. Anyone else see this?
    '06 Outback - Gone but not forgotten
    '13 Mojo

  3. #23
    Join Date
    Dec 2012
    Location
    Ennis, TX
    Posts
    180

    Default Sloppy Swim Platform - '13 Mojo

    Work with your dealership. I had mine replaced with the 14 platform brackets for around 250 out of pocket. Normally would run over a grand. Dealership ate the labor and gel work and SC helped with the bracket exchange. The new brackets are stainless with no slop at all.


    Sent from my iPhone using Tapatalk
    Shane
    2012 Mojo 2.5
    EXILED
    4 XM9 Tower
    6 SX65M Cabin
    1 XI 800.4
    1 XI 1500.1
    1MX 30.2
    EXILE ZLD
    Green LEDs

  4. #24
    Join Date
    Jul 2013
    Location
    Cedar Falls, IA
    Posts
    401

    Default Sloppy Swim Platform - '13 Mojo

    I'm looking at doing the same thing, problem is my dealer doesn't do gel work so I'd have to take it somewhere for hat part of the work. I'm sure I'll be in a little more $ to get mine done.

    I did replace the hardware, helps some.



    Sent from my iPhone using Tapatalk
    2013 Moomba Mojo 2.5
    Exile SXT9's, Xi12D, Javelin, 800.4, ZLD MKII

    2012 F150 Ecoboost

  5. #25
    Join Date
    May 2009
    Location
    Carlton Oregon
    Posts
    6,020

    Default

    I think I might have been one of the first to do this this year. I was able to get SC to work with me and my dealer as part of a warranty. My brackets where really worn down plus I had longer screws installed that where all bent.

    Very worth every dollar.
    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    Exile ZLD
    6 SX65M Cabins
    6 XM9 Towers
    1 XI Big 15 Woofer in a custom Fiberglass box
    1 XI 1K Harpoon
    2 XI 800.4
    1 XI 2500.1
    2 Interstate 2400U 6V Golf Cart Batterties
    Custom 1 Off Evolution Cover

  6. #26
    Join Date
    Jul 2013
    Location
    Whiteshell, MB
    Posts
    23

    Default

    Can anyone post a picture(s) with the old and new versions side by side?
    2012 Mojo2.5
    Ballast:
    1100 surf side
    400 goofy side
    500 under floor
    725 IBS
    260 bow floor
    (The more spotters the better)
    Acme1235

  7. #27
    Join Date
    May 2009
    Location
    Carlton Oregon
    Posts
    6,020

    Default

    I don't have any of the 13 brackets pictured from my Mojo.

    Here is my 08 LSV with the same brackets they used up through 12 model year.


    New 14 style after they replaced the factory 13s. Honestly you can't see any gell work or anything. Dealer said its almost a direct bolt up. They have to redril the platform mounts under the swim deck. They used RTV to seal the old screw holes.





    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    Exile ZLD
    6 SX65M Cabins
    6 XM9 Towers
    1 XI Big 15 Woofer in a custom Fiberglass box
    1 XI 1K Harpoon
    2 XI 800.4
    1 XI 2500.1
    2 Interstate 2400U 6V Golf Cart Batterties
    Custom 1 Off Evolution Cover

  8. #28
    Join Date
    Jun 2013
    Location
    Naperville, IL || North Scott Lake, MI
    Posts
    658

    Default

    I don't have any good pics, but I'm pretty sure my '13 OBV brackets look pretty much the same as Mike's pics of his old '08....
    Mike

    2013 Outback V
    2003 SeaRay 182 -- gone but not forgotten...

  9. #29
    Join Date
    Oct 2008
    Location
    Arkansas
    Posts
    647

    Default

    New brackets were not introduced until '14, unless you have had a warranty claim done since. '13 brackets were similar to Mike's post except they added the set screw.

  10. #30
    Join Date
    Jul 2013
    Location
    Whiteshell, MB
    Posts
    23

    Default

    Thanks, mine seems to be holding in there but we dont get the hours on it that i'd like. I'm going to speak with my dealer and see how big a deal it is...
    2012 Mojo2.5
    Ballast:
    1100 surf side
    400 goofy side
    500 under floor
    725 IBS
    260 bow floor
    (The more spotters the better)
    Acme1235

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •