Page 3 of 3 FirstFirst 123
Results 21 to 28 of 28
  1. #21
    Join Date
    Jul 2008
    Location
    Des Moines, IA
    Posts
    2,581

    Default No more wet lockers.

    When the carpet is soaked it pulls out easier and brings more adhesive with it in my experience. My total time was only a few hours tops. I used a razor scraper then acetone to get the remaining adhesive off.

  2. #22
    Join Date
    Jun 2007
    Location
    Rice Lake, Ontario
    Posts
    626

    Default

    Last edited by spyder; 09-02-2014 at 02:06 PM.
    2006 Moomba Mobius LSV
    Lake: Rice lake, Ontario
    Stereo: Kenwood KMR-550U
    Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
    Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"

    If you're from the area and want to surf, send me a PM!

  3. #23
    Join Date
    Jun 2007
    Location
    Vancouver, WA
    Posts
    4,030

    Default

    Quote Originally Posted by brain_rinse View Post
    When the carpet is soaked it pulls out easier and brings more adhesive with it in my experience.
    I'm wondering if hot/boiling water may be the ticket? Also an off-season plan.
    Old enough to know better, young enough to do it anyway.

    2001 MobiusV

  4. #24
    Join Date
    Jul 2008
    Location
    Des Moines, IA
    Posts
    2,581

    Default No more wet lockers.

    Or heat gun maybe?

  5. #25
    Join Date
    Nov 2013
    Posts
    173

    Default

    I went with Herculiner because it was $40 cheaper than the Duplicolor. It is still going strong, no rips or tears. No mold, no stinky mess. Definitely buy the gallon if you plan to coat the sides. The herculiner instructions say to thin it with Xylene. Xylene removes adhesive/grease very well, but is apparently hard on fiberglass. I never needed to thin my liner as the coats were quick and temps were cool. But inna few small spots I did use Xylene to clear some built up glue. It didn't seem to harm the fiberglass, bit I spilled about a cup on my swim deck and it permanently stained the factory rubber mat. I would use caution with any strong solvent around fiberglass.
    2007 LSV

  6. #26
    Join Date
    Jun 2007
    Location
    Rice Lake, Ontario
    Posts
    626

    Default

    Quote Originally Posted by Beejwest View Post
    I went with Herculiner because it was $40 cheaper than the Duplicolor. It is still going strong, no rips or tears. No mold, no stinky mess. Definitely buy the gallon if you plan to coat the sides. The herculiner instructions say to thin it with Xylene. Xylene removes adhesive/grease very well, but is apparently hard on fiberglass. I never needed to thin my liner as the coats were quick and temps were cool. But inna few small spots I did use Xylene to clear some built up glue. It didn't seem to harm the fiberglass, bit I spilled about a cup on my swim deck and it permanently stained the factory rubber mat. I would use caution with any strong solvent around fiberglass.
    good to know, can't seem to find Herculiner in Canada... anyone have a source?
    2006 Moomba Mobius LSV
    Lake: Rice lake, Ontario
    Stereo: Kenwood KMR-550U
    Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
    Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"

    If you're from the area and want to surf, send me a PM!

  7. #27
    Join Date
    Nov 2013
    Posts
    173

    Default

    Probably just have to order it....


    http://www.amazon.com/Herculiner-HCL.../dp/B0002TDUW4
    2007 LSV

  8. #28
    Join Date
    Jun 2007
    Location
    Rice Lake, Ontario
    Posts
    626

    Default

    Quote Originally Posted by Beejwest View Post

    no dice.. no shipping to Canada..

    Sorry, this item can't be shipped to your selected address

    This is what we had at Canadian Tire

    2006 Moomba Mobius LSV
    Lake: Rice lake, Ontario
    Stereo: Kenwood KMR-550U
    Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
    Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"

    If you're from the area and want to surf, send me a PM!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •