Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20
  1. #11
    Join Date
    Jan 2008
    Location
    Keuka Lake, NY
    Posts
    5,812

    Default

    take it apart and hook to a 12 v battery and see if it works. I use my jumper pack all the time to test things.
    The Wal-Mart one had cut wires no harness, plus that harness does not match what SC uses, the deutch plugs

    http://www.deutschconnector.com/prod...ay_connectors/
    Last edited by jmvotto; 07-21-2014 at 10:20 AM.
    A Day at the Lake...Priceless
    A Day in Powder...Endless


    Joe V
    2012 Möbius XLV~ Loaded & Exiled
    2007 Outback V ~ sold

  2. #12
    Join Date
    Mar 2013
    Location
    Madison, AL
    Posts
    83

    Default

    I went through this last year and replaced mine. I used to know where to order the triangle plug from but I cant remember at the moment. I redid mine and shrink wrapped all the new wiring with my heat gun. Note: Make sure when you install the new one to get it at the lowest point in the hull to help with the water.
    2005 Moomba Mobius LSV
    ACME 1433 prop (newest upgrade)
    1900lbs Surf side

  3. #13
    Join Date
    Jun 2007
    Location
    Rice Lake, Ontario
    Posts
    626

    Default

    Quote Originally Posted by Jayrodau View Post
    I went through this last year and replaced mine. I used to know where to order the triangle plug from but I cant remember at the moment. I redid mine and shrink wrapped all the new wiring with my heat gun. Note: Make sure when you install the new one to get it at the lowest point in the hull to help with the water.
    Thanks, was going to shrink wrap it... since getting a new plug probably wont be possible in time.
    2006 Moomba Mobius LSV
    Lake: Rice lake, Ontario
    Stereo: Kenwood KMR-550U
    Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
    Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"

    If you're from the area and want to surf, send me a PM!

  4. #14
    Join Date
    Jan 2008
    Location
    Keuka Lake, NY
    Posts
    5,812

    Default

    the above link has the triangle plug as well. SC uses the square two pin.
    A Day at the Lake...Priceless
    A Day in Powder...Endless


    Joe V
    2012 Möbius XLV~ Loaded & Exiled
    2007 Outback V ~ sold

  5. #15
    Join Date
    Jun 2007
    Location
    Rice Lake, Ontario
    Posts
    626

    Default

    btw, repair was quick and easy... remembered how bad I am at soldering. the heat shrink made it look good though..


    note: know what took down the old bilge? it sucked up a piece of plastic of some sort... burned itself out auto bilging overnight.
    2006 Moomba Mobius LSV
    Lake: Rice lake, Ontario
    Stereo: Kenwood KMR-550U
    Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
    Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"

    If you're from the area and want to surf, send me a PM!

  6. #16
    Join Date
    Jan 2008
    Location
    Tallahassee, FL
    Posts
    11,239

    Default

    Heat shrink makes us all look like pros! (Except for the guy who set the soldering iron down on the seat and burned a hole through it.)
    My Mom said I'm not allowed to get wet!
    2008 LSV
    2000 Outback LS (sold)
    Exile Tunes
    PWI
    LLTR!!!!!!!!



  7. #17
    Join Date
    Jun 2007
    Location
    Rice Lake, Ontario
    Posts
    626

    Default

    Quote Originally Posted by kaneboats View Post
    Heat shrink makes us all look like pros! (Except for the guy who set the soldering iron down on the seat and burned a hole through it.)
    i made sure to take everything i needed outside the boat on the picnic table.. and still did it on a chunk of extra wood
    2006 Moomba Mobius LSV
    Lake: Rice lake, Ontario
    Stereo: Kenwood KMR-550U
    Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
    Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"

    If you're from the area and want to surf, send me a PM!

  8. #18
    Join Date
    Jan 2008
    Location
    Keuka Lake, NY
    Posts
    5,812

    Default

    I always brought a cardboard box in the boat with extra card board inside to make the soldering iron stays in the box or above the box, plus one on heat shrink.

    Glad it was a fairly straight forward fix.
    A Day at the Lake...Priceless
    A Day in Powder...Endless


    Joe V
    2012 Möbius XLV~ Loaded & Exiled
    2007 Outback V ~ sold

  9. #19
    Join Date
    Jan 2008
    Location
    Tallahassee, FL
    Posts
    11,239

    Default

    Well, I had a "matt" down and then bumped the cord, twisted the iron right off the matt and smelled the result.
    My Mom said I'm not allowed to get wet!
    2008 LSV
    2000 Outback LS (sold)
    Exile Tunes
    PWI
    LLTR!!!!!!!!



  10. #20
    Join Date
    Jun 2007
    Location
    Rice Lake, Ontario
    Posts
    626

    Default

    Quote Originally Posted by kaneboats View Post
    Well, I had a "matt" down and then bumped the cord, twisted the iron right off the matt and smelled the result.
    ughhhhhhh
    2006 Moomba Mobius LSV
    Lake: Rice lake, Ontario
    Stereo: Kenwood KMR-550U
    Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
    Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"

    If you're from the area and want to surf, send me a PM!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •