Results 1 to 10 of 12

Hybrid View

  1. #1
    Join Date
    Jan 2008
    Location
    Atlanta via Pittsburgh
    Posts
    84

    Default 2008 LSV seat swivel

    I finally finished my seat swivel for 2008 LSV. I'm trying to figure out the pictures so bare with me.
    Attached Images Attached Images
    Go Boat

  2. #2
    Join Date
    Jan 2008
    Location
    Atlanta via Pittsburgh
    Posts
    84

    Default Part 2

    Part 2 pictures In these pictures the swivel bracket is not in line with the seat slider rails because I was afraid the seat would hit the side when turned. I've gone back and moved the swivel bracket so that it sits directly over the rails and the seat does not hit. This also allowed the seat to be centered with the steering wheel.
    Attached Images Attached Images
    Last edited by chillyx; 02-24-2009 at 01:23 PM.
    Go Boat

  3. #3
    Join Date
    Jan 2008
    Location
    Atlanta via Pittsburgh
    Posts
    84

    Default Part 3

    I couldn't figure out how to post a picture with text without doing one pic per post.

    So I'm going to try to follow the picture sequence with these instructions.

    1. Remove the seat from the bracket
    2. I cut a piece of the "kingboard" they gave me with the boat to hold up the tower. I cut it large enough to bolt onto the seat slider.
    3. I screwed the swivel to the kingboard. (directly over the slider rails but toward the back to change the center of rotation so the corners would not hit while swiveling)
    4. I cut another piece to place on top of the swivel in order to bolt the seat to. I bolted this piece to the swivel. I had to counter sink the bolts down into the board so the set would sit flush. There were places on the bottom of the seat I could have used to attach to the swivel but I want to scootch the seat over to make sure it didn't rub the side.
    5. I used a piece of the scrap to make a small elevator piece to level out the seat, so that when the seat was swiveled it wouldn't get pitched forward.

    The last picture is of all the pieces sandwiched together. The only drawback is it raises the seat about 3.5 to 4 inches which actually works out for me because I always end up sitting on a cushion anyway.

    I hope this helps.
    Attached Images Attached Images
    Last edited by chillyx; 02-24-2009 at 01:48 PM. Reason: left a part out
    Go Boat

  4. #4
    Join Date
    Nov 2003
    Location
    Land O Lakes, Florida
    Posts
    5,889

    Default

    chillyx, well done and looks good
    Hey, Its Moomba time

    13 Mobius LSV
    08 Mobius LSV-sold
    03 Mobius LSV-sold
    life is about finding the balance between being a responsible adult and staying young at heart

  5. #5
    Join Date
    Feb 2008
    Location
    Traverse City, MI
    Posts
    2,408

    Default

    Very cool! Is that the same style swivel I had? Loos like it - I need to finish that project!

  6. #6
    Join Date
    Apr 2007
    Location
    Las Vegas, Nevada
    Posts
    1,582

    Default

    Very Nice. Were did you get the swivel bracket? Is it the same as Ian swivel?
    Tazz 07' Moomba LSV --Kicker Marine Amps (MX700.5 & MX350.4) 6 polk DB651 speakers, 4 MB Quartz Marine Speakers, 10" Boston Acoustic Sub, Z-5 Cargo Rack, Custom Speaker/Light Bar, modified ballast system, Custom LED Rings
    Live life to the extreme and no less!!

  7. #7
    Join Date
    Nov 2003
    Location
    Land O Lakes, Florida
    Posts
    5,889

    Default

    Quote Originally Posted by chillyx View Post
    5. I used a piece of the scrap to make a small elevator piece to level out the seat, so that when the seat was swiveled it wouldn't get pitched forward.

    chillyx, any way to explain this part a little bit more? I dont quite understand the elevator part.

    Thanks
    Hey, Its Moomba time

    13 Mobius LSV
    08 Mobius LSV-sold
    03 Mobius LSV-sold
    life is about finding the balance between being a responsible adult and staying young at heart

  8. #8
    Join Date
    Jan 2008
    Location
    Atlanta via Pittsburgh
    Posts
    84

    Default The elevator

    I realized when I wrote that, that it didn't make any sense and I should not be a technical writer. The elevator is actually a spacer. I put it in to raise the back of the seat. On my LSV the platform that the seat is mounted to is tilted back, so when I would rotate around it actually pitched me forward. I put in the spacer to level the seat. Hope this helps. I have some other things to explain better, like the seat being off center. I will do this with a diagram tomorrow morning hopefully.
    Go Boat

  9. #9
    Join Date
    Feb 2008
    Location
    Arvada , Colorado
    Posts
    267

    Default seat swivel

    So how does it work? I have an 05 Mobius lsv and would like to do the same thing , also raise the seat 2-3" also. Thanks, Jim .
    05 Mobius lsv , ballast system , stereo, etc..

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •